background image

..\Manuals\RCI-800-RF9 rev.B.doc 

                                                                                                          Page 9 of 10 

Next, set the 

number of channels of each remote

 using SW2-1, 

-2.  One channel is considered 1 analog input/output plus 1 
contact input/output. Hence an RCI-800 can have at most 8 
channels. 
 
Next, set the 

number of channels of the host

 using SW2-3, -4.  

An RCI-800 can at most have 8 channels.  This is the number of 
channels that will be exchanged between the host and each 
remote. 
 

Remote Configuration:

 

 
To make an RCI-800 operate as a REMOTE unit, make sure that SW2-8 is flipped up. 
 
Next, set the 

remote address

 using SW1-1, -2 & -3.  Each 

remote in a system must have a unique address. 
 
 
 
 
 
 
Next, set the 

number of channels on this remote

 using SW2-1, 

-2.  One channel is considered 1 analog input/output plus 1 
contact input/output. Hence an RCI-800 can have at most 8 
channels. 
 

Perform the next step only if this remote is communicating to the host via a repeater!!! 

 
When the remote is linked to a repeater the 

remote PHP

 

must be set using SW1-4, -5, -6.  The PHP of the remote 
must match the SHP of the repeater. 
 
 
 
 

 

Received Signal Strength Indicator (RSSI):

 

 
 The radio communications board has a signal strength 
indicator to show the level of the signal that was received 
from another radio.  The indicator consists of 3 LED’s 
labeled 1, 2 & 3.  It is desirable to operate with the highest 
signal strength achievable.  If the signal strength is less than 
-93 dBm, it is advisable to try to make adjustments to 
then system to bring the signal strength up.  A higher 
power setting on the radio or a higher gain antenna 
can be used to increase signal strength and achieve 
more reliable operation of the radio system. 
 
 

SW2-1 

SW2-2 

Channels on Remotes 

UP UP 

DOWN UP 

UP DOWN 

DOWN DOWN 

SW2-3 

SW2-4 

Channels on Host 

UP UP 

DOWN UP 

UP DOWN 

DOWN DOWN 

SW1-1 

SW1-2 

SW1-3 

Remote Address 

UP UP  UP 

DOWN UP  UP 

UP DOWN  UP 

DOWN DOWN  UP 

UP UP 

DOWN 

DOWN UP  DOWN 

UP DOWN 

DOWN 

DOWN DOWN  DOWN 

SW2-1 

SW2-2 

Channels on Remote 

UP UP 

DOWN UP 

UP DOWN 

DOWN DOWN 

SW1-4 

SW1-5 

SW1-6 

REMOTE PHP 

UP UP  UP 

DOWN UP  UP 

UP DOWN  UP 

DOWN DOWN  UP 

UP UP 

DOWN 

DOWN UP  DOWN 

UP DOWN 

DOWN 

DOWN DOWN  DOWN 

Signal Strength 

(dBm) 

LED 1 

LED 2 

LED 3 

-108 Flashing Off 

Off 

-101 On Off Off 

-93 On

 

Flashing Off 

-86 On

 

On

 

Off 

-79 On

 

On

 

Flashing 

-71 On

 

On

 

On 

Summary of Contents for RCI-800-RF9

















Reviews: