background image

 I

NSTALLATION

 : I

NSTALLATION

 P

ROCEDURE

0 2. 9 8 1 2. 0 0 01 A

11

2

Installation Procedure

Installing Luminaire in a Hanging Configuration

The Bad Boy™ Spot Luminaire can be hung horizontally or vertically from any structure designed to 
accommodate the load of this moving luminaire. Two provided Hanging Bracket Assemblies 
(21.9812.0863) are used to attach the luminaire to a truss pipe. The Hanging Brackets consist of a pre-
assembled bracket with a Mega-Claw Truss Hook. 

To unpack and attach brackets:

Step 1. Unlatch and remove case lid (

Figure 2-2

).

Step 2. Remove Power Cord, Safety Cables, and Hanging Brackets from case.
Step 3. Tilt luminaire enclosure upright as shown.
Step 4. Install Hanging Brackets as follows:

a. Choose orientation. Brackets may be attached in one of four positions. Refer to 

Figure 

2-3

 for a diagram of the orientation options.

b. Orient Hanging Bracket in desired direction over two attachment buttons on bottom of 

upper enclosure (

Figure 2-2

). 

c. Place Hanging Bracket down over buttons and slide until bracket locks into place (you 

will hear a "click" when bracket is locked).

Figure 2-2:  Opening Case and Attaching Hanging Brackets

Hanging Bracket (2)

Safety Cable (2)

Power Cord

Case

Summary of Contents for BAD Boy













































































Reviews: