Prestige APS-596E Owner'S Manual Download Page 19

Page: 19 / 20

128-9315

19 of 20

Page 19

APS 596E

SYSTEM FUNCTIONS AT A GLANCE

DASH LED INDICATORS

RAPID FLASHING

PASSIVE ARMING/ACTIVE

REARMING

SLOW FLASHING

ARMED

OFF

= DISARMED

ON SOLID

VALET MODE

3 FLASH...PAUSE

INTRUSION ZONE 3

2 FLASH...PAUSE

INTRUSION ZONE 2

1 FLASH...PAUSE

INTRUSION ZONE 1

SIREN CHIRP INDICATORS

1 CHIRP *

ARM

2 CHIRPS *

DISARM

3 CHIRPS

ARM / DOOR OPENED

4 CHIRPS

DISARM / INTRUSION

* These chirps are optional, and can be de - activated.

PARKING LAMP INDICATORS

1 FLASH

ARM

2 FLASHES

DISARM

3 FLASHES

DISARM / INTRUSION

Transmitter Battery Replacement

1) Locate and remove the "00" point Phillips head screw on the back of the transmitter

case.

2) Carefully separate the front case from the rear.

3) Slide the CR2032 battery out from under the battery clip and dispose of properly.

4) Install the new battery with the (+) side facing up away from the circuit board.

5) Close the case and reassemble in reverse of disassembly

LCD Transmitter Battery Replacement

1) Locate Battery Compartment Cover on rear of case.

2) Lift the edge slightly while sliding the cover away from the transmitter.

3) Remove the AAA battery paying attention to the + & - orientation of the battery.

4) Replace the battery with a new AAA and dispose of the used battery properly.

5) Slide the cover back in place making sure it is firmly seated.

Summary of Contents for APS-596E





















Search results

Summary of Contents for APS-596E

Reviews:

Brands by name

Popular brands

Prestige APS-596E, Owner'S Manual

Search results

Summary of Contents for APS-596E

Reviews:

Brands by name

Popular brands