background image

128-9315  of  

16 of 20

Page 16

Z

Z

PRESTIGE

IGN

AM

PM

Z

Z

24

S

1 2

INHIBIT

A

0

PRESTIGE

1 2

3 Hrs and 45 Mins. This additional count down timer allows you to set the count 

down up 19 Hours and 59 Minutes from the current time and when the timer 

reaches zero, the transmitter will emit a tone or vibrate dependent on your pre

-

ferred setting.  See chart for setting the count down time for this feature.    

 Valet

When the System is in the valet mode, the icon shown will show in the 

display when the status check buttons are activated.

 Parking Meter Counter

The transmitter has a built in clock that can count down from 10, 20, 30, 60, 90, or 

120 minutes.  This feature is useful when parking the vehicle in a metered parking 

lot.  If the time on the parking meter is 30 minutes, you can set the count down 

timer to 20 minutes.  The transmitter will emit a beep tone when the timer expires 

to remind you to get back to your vehicle. See following chart for setting the park-

ing meter count down timer feature. 

 Alarm Clock Mode

The transmitter has a built in alarm clock that can be set to beep at a 

certain time each day.  The alarm clock mode must be set, and the feature 

turned on.  To use this feature please refer to the chart on the following 

page.

NOTE:

  Your system is shipped with two transmitters, 1 two way, shown on the 

left and the one way transmitter, shown right.  The one and two way transmitters 

are programmed from the factory with separate lock & unlock buttons, the trunk/

key icon button operates remote start and remote trunk release where applicable.  

The option button and any button combination may be programmed to operate 

various options.  Consult your installation center for button programming and 

options that may have been added to your vehicle.    Although this is the default 

programming from the factory, this can be changed for you to any configuration 

you prefer.  Please refer to the transmitter program guides included with your kit.

NOTE: 

 A maximum of two of either style transmitter may be programmed to your 

unit.

 BATTERY INDICATOR  

Your transmitter has a battery indicator that is 

shown in the upper right corner of the screen 

as shown left.  This icon indicates a new bat-

tery shown with 3 bars.  As the battery deteriorates, 

the bars will disappear.  1 bar indicates the battery 

should be replaced. Replace battery with a fresh 1.5V 

AAA battery and dispose of the used battery properly.

Other icons that will be displayed at times when cer-

tain functions and features are active in the vehicle or 

on the remote.

 RANGE INDICATOR  

The range indicator will have bars to the side of the icon if the unit is out of 

range.

Summary of Contents for APS-596E





















Reviews: