Presenza QK032 Installation Manual And User'S Manual Download Page 13

13

CONGLOMKB .COM

Please contact customer .service@conglomkb .com or 1-877-333-0098 for further assistance .

 

Care and Cleaning

 

SINK, SLIDING SINK AND COLANDER

Your sink is manufactured with the highest grade stainless steel and will provide you many years of enjoyment with the proper care .

Do

Do Not

 

- After use, always rinse your sink with tap water to 

dilute and remove deposits .

 

- Towel dry the sink after use whenever possible 

to prevent water spots . Should water spots occur, 
clean with a mild solution of vinegar and water 
followed by a thorough rinse .

 

- Use liquid soap, a general household cleaner, or 

a weak solution of vinegar and water for regular 
cleaning .

 

- Only use plastic scouring pads recommended for 

use in stainless steel sinks, and only use them in 
the bowl of the sink . Scrub in the direction of the 
grain (original polish lines) .  

 

- Do not allow any food, detergent, soap or grease 

to dry or sit for extended periods of time on the 
surface of the sink .

 

- Never use abrasive cleaning products, as they will 

dull and scratch the finish.

 

- Do not use scouring pads on the deck, as they will 

dull the mirror finish.

 

- Never use steel wool pads, as they will leave iron  

particles on the sink, which will cause corrosion .

 

- Never leave mild steel or cast iron pans in your 

sink for extended periods of time, as this can cause 
corrosion .

CUTTING BOARD

Do

Do Not

 

- Before using your new bamboo cutting board, oil 

with mineral oil . Apply oil to your cutting board 
with a cotton cloth . Rub in thoroughly . Let board sit 
for approximately 15-20 minutes before removing 
excess oil . Then apply oil once a month for light 
usage and up to once a week for boards that are 
used more often . 

 

- After each use, wash your bamboo cutting board 

with a mild dish detergent and warm water . Wipe 
board dry immediately after use . 

 

-

Sanitize your board after coming in contact 

with raw meat by using a solution of vinegar or 
hydrogen peroxide and water or a bleach dilution . 
Be sure to rinse board thoroughly .

 

- Do not put your cutting board in the dish washer 

and do not soak .

 

- Never put your bamboo cutting board in the 

microwave .

Summary of Contents for QK032
















Reviews: