background image

Page 23

For technical questions, please call 1-800-520-0882.

Item 60349 

        

Warranties

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and 

warrants to the original purchaser that this product is free from defects in materials and workmanship for the period 

of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, 

abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, 

normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or 

property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some 

states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of 

exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, 

EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. 

Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection 

verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase 

price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, 

but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, 

then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Emission Control System Warranty

United States Emission Control Defects Warranty 

Statement

The United States Environmental Protection Agency (herein EPA) 

and Harbor Freight Tools (herein HFT) are pleased to explain the 

emission control system warranty on your 1997 and later Small Off-

Road Engine (herein engine). Within the United States, new off-road, 

spark-ignition engines certified for model year 1997 and later, must be 

designed, built and equipped to meet the stringent anti-smog standards 

set forth by the EPA.  HFT must warrant the emission control system on 

your engine for the periods of time described below, provided there has 

been no abuse, neglect or improper maintenance of your engine.

Your emission control system may include parts such as the 

carburetor or fuel-injection system, and the ignition system. Also 

included may be hoses, belts, connectors and other emission-related 

assemblies.

Where a warrantable condition exists, HFT will repair your engine 

at no cost to you including diagnosis, parts and labor.

Manufacturer’s Warranty Coverage

The 1995 and later engines are warranted for two (2) years.  If 

any emission-related part on your engine is defective, the part will be 

repaired or replaced by HFT.

Harbor Freight Tools Emission Control Defects 

Warranty Coverage

Engines are warranted for a period of two (2) years relative to 

emission control parts defects, subject to the provisions set forth below. 

If any emission related part on your engine is defective, the part will be 

repaired or replaced by HFT.

 

Owner’s Warranty Responsibilities

•  As the engine owner, you are responsible for the performance 

of the required maintenance listed in your Owner’s Manual. HFT 

recommends that you retain all receipts covering maintenance 

on your engine, but HFT cannot deny warranty solely for the lack 

of receipts or for your failure to ensure the performance of all 

scheduled maintenance.

•  As the engine owner, you should, however, be aware that HFT 

may deny you warranty coverage if your engine or a part has failed 

due to abuse, neglect, improper maintenance, or unapproved 

modifications.

•  You are responsible for shipping your engine to a HFT warranty 

station as soon as a problem exists.  Contact the HFT Customer 

Service department at the number below to make shipping 

arrangements.  The warranty repairs should be completed in a 

reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and 

responsibilities, you should contact the Harbor Freight Tools Customer 

Service Department at 1-800-520-0882.

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Summary of Contents for 60349

























Reviews: