background image

Choose a Program

• Determine your level of fitness: beginner,

intermediate, or advanced.

• Determine your immediate goal: endurance

training, cardio-conditioning, or weight loss.

If you are a beginner, start with a cardio-conditioning
program to gradually adjust your body to the demands of 
exercise. Over a recommended eight-week period, you will 
increase your endurance and strength.

For all fitness levels, plan to exercise at an appropriately 
challenging pace for 20 to 30 minutes a day. Wear a chest 
strap to monitor your heart rate. Supplement your plans 
with fitness workouts from the Precor web site  
(www.precor.com). The Precor web site also provides 
expert advice to help you reach your fitness goals.

monitor Your heart rate

The SmartRate and heart rate displays provide visual cues 
that help you adjust your fitness routine to reach your 
goals. Use these features to keep your heart rate within 
the target zones.

Wear a Chest Strap

During a workout, the heart rate features appear on 
the display when you wear a chest strap. To receive an 
accurate reading, the chest strap needs to be in direct 
contact with your skin. After you put on the chest strap, 
face the display console for a minimum of 15 seconds. This 
allows the receiver in the console to recognize the signal 
from the chest strap.

1. Carefully dampen the back of the strap with tap

water (Diagram A).

Important: 

Do not use deionized water. It does

not have the proper minerals and salts to conduct
electrical impulses.

2. Adjust the strap and fasten it around your chest.

The strap should feel snug, not restrictive
(Diagram B).

3. Make sure that the chest strap is right side up, lies

horizontally across your chest, and is centered in
the middle of your chest (Diagram C).

When these steps are complete, you are ready to view
your heart rate.

touch-Sensitive Handrail Grips

Several Precor products incorporate touch-sensitive
heart rate grips on the handrails. If you prefer to use
the touch-sensitive handrail grips, use both hands.
Make sure both hands are moist (not dry) and avoid 
grasping the sensors too tightly.

note:

 For the best heart rate monitoring results, wear a 

chest strap.

smartrate® Features

When you begin an exercise session, a blinking
segment in the SmartRate display appears if you
entered your age during the setup phase. The blinking
segment indicates the current zone of your heart rate.

The calculation used for the heart rate target zone is
your maximum aerobic heart rate:
(220 minus your age), multiplied by a percentage.

For the ideal weight loss range, your heart rate should
remain between 55% and 69% of your maximum

aerobic heart rate. To improve your overall
cardiovascular and respiratory fitness level, maintain  
your heart rate between 70% and 85% of your
maximum aerobic heart rate. For the greatest benefits, 
maintain your heart rate in either zone for 30 minutes or 
more at least three times a week.

CaUtIon: Your heart rate should never exceed

85% of your maximum aerobic heart rate or go

above your target zone (Diagram D).

Cool Down aFter Your workout

Cooling down is an important aspect of your workout
because it helps reduce muscle stiffness and
soreness by transporting excess lactic acid out of the
working muscles. Cooling down for at least three
minutes helps provide a smooth transition that allows
your heart rate to return to its normal, non-exercising state.

20031 142nd Avenue NE   |   P.O. Box 7202
Woodinville, WA USA 98072-4002
www.precor.com
P/N 303208-111   |   ©2014 Precor Incorporated

Diagram A

Diagram B

Diagram C

Choose a Program

Determine your level of fitness: beginner, 
intermediate, or advanced.

Determine your immediate goal: endurance 
training, cardio-conditioning, or weight loss.

If you are a beginner, start a cardio-conditioning 
program to slowly adjust your body to a comfortable 
level of exercise. Over a recommended 8-week 
period, you will increase your endurance and strength 
while improving flexibility. 

If you have been exercising and feel that you have 
reached an intermediate or advanced fitness level, you 
probably have established goals for yourself. 

For all fitness levels, plan to exercise at a comfortable 
pace for 20 to 30 minutes a day. Wear a chest strap 
to monitor your heart rate. Supplement your plans 
with fitness workouts from the Precor web site 
(www.precor.com). The Precor web site also provides 
expert advice to help you reach your fitness goals.

Monitor Your Heart Rate

The SmartRate and heart rate displays provide visual 
cues that help you adjust your fitness routine to reach 
your goals. Use these features to keep your heart rate 
within the target zones.

Wear a Chest Strap

During a workout, the heart rate features appear on 
the display when you wear a chest strap. To receive 
an accurate reading, the chest strap needs to be in 
direct contact with your skin. After you put on the 
chest strap, face the display console for a minimum of 
15 seconds. This allows the receiver in the console to 
recognize the signal from the chest strap. 

1. Carefully dampen the back of the strap with tap 

water (Diagram A).

Important: 

 Do not use deionized water. It does 

not have the proper minerals and salts to conduct 
electrical impulses.

2. Adjust the strap and fasten it around your chest. 

The strap should feel snug, not restrictive 
(Diagram B).

3. Make sure that the chest strap is right side up, lies 

horizontally across your chest, and is centered in 
the middle of your chest (Diagram C).

When these steps are complete, you are ready to view 
your heart rate!

Touch-Sensitive Handrail Grips

Several Precor products incorporate touch-sensitive 
heart rate grips on the handrails. If you prefer to use 
the touch-sensitive handrail grips, use both hands. 
Make sure both hands are moist (not dry) when you 
grasp the touch-sensitive handrail grips. 

SmartRate

®

 Features

When you begin an exercise session, a blinking 
segment in the SmartRate display appears if you 
entered your age during the setup phase. The blinking 
segment indicates the current zone of your heart rate. 

The calculation used for the heart rate target zone is 
your maximum aerobic heart rate: 
(220 minus your age) multiplied by a percent. 

For the ideal weight loss range, your heart rate should 
remain between 55% and 70% of your maximum 
aerobic heart rate. To improve your overall 
cardiovascular and respiratory fitness level, maintain 
your heart rate between 70% and 85% of your 
maximum aerobic heart rate. 

For the greatest benefits, maintain your heart rate in 
either zone for 30 minutes or more at least three times 
a week.

CAUTION: Your heart rate should never exceed 
85% of your maximum aerobic heart rate or go 
above your target zone (Diagram D).

Diagram D

Cool Down After Your Workout

Cooling down is an important aspect of your workout 
because it helps reduce muscle stiffness and 
soreness by transporting excess lactic acid out of the 
working muscles. Cooling down for at least three 
minutes helps provide a smooth transition that allows 
your heart rate to return to its normal, non-exercising 
state.

Diagram A

Diagram B

Diagram C

20 25 30 35 40 45 50 55 60 65 70 75

70

80

90

100

120

130

140

150

160

170

180

190

200

110

Heart Rate Target Zones

Your Age

Y

o

u

r Hea

rt R

a

te

Peak

Cardio

Warmup

Reco

mmen

ded C

ardio

vascu

lar Zo

ne

Recom

mende

d Weig

ht Loss

 Zone

Fatburn

High

Precor Incorporated

20031 142nd Avenue NE

P.O. Box 7202

Woodinville, WA USA 98072-4002

www.precor.com

HR INFO 48140-104

©2007

 

Precor Incorporated

Choose a Program

Determine your level of fitness: beginner, 
intermediate, or advanced.

Determine your immediate goal: endurance 
training, cardio-conditioning, or weight loss.

If you are a beginner, start a cardio-conditioning 
program to slowly adjust your body to a comfortable 
level of exercise. Over a recommended 8-week 
period, you will increase your endurance and strength 
while improving flexibility. 

If you have been exercising and feel that you have 
reached an intermediate or advanced fitness level, you 
probably have established goals for yourself. 

For all fitness levels, plan to exercise at a comfortable 
pace for 20 to 30 minutes a day. Wear a chest strap 
to monitor your heart rate. Supplement your plans 
with fitness workouts from the Precor web site 
(www.precor.com). The Precor web site also provides 
expert advice to help you reach your fitness goals.

Monitor Your Heart Rate

The SmartRate and heart rate displays provide visual 
cues that help you adjust your fitness routine to reach 
your goals. Use these features to keep your heart rate 
within the target zones.

Wear a Chest Strap

During a workout, the heart rate features appear on 
the display when you wear a chest strap. To receive 
an accurate reading, the chest strap needs to be in 
direct contact with your skin. After you put on the 
chest strap, face the display console for a minimum of 
15 seconds. This allows the receiver in the console to 
recognize the signal from the chest strap. 

1. Carefully dampen the back of the strap with tap 

water (Diagram A).

Important: 

 Do not use deionized water. It does 

not have the proper minerals and salts to conduct 
electrical impulses.

2. Adjust the strap and fasten it around your chest. 

The strap should feel snug, not restrictive 
(Diagram B).

3. Make sure that the chest strap is right side up, lies 

horizontally across your chest, and is centered in 
the middle of your chest (Diagram C).

When these steps are complete, you are ready to view 
your heart rate!

Touch-Sensitive Handrail Grips

Several Precor products incorporate touch-sensitive 
heart rate grips on the handrails. If you prefer to use 
the touch-sensitive handrail grips, use both hands. 
Make sure both hands are moist (not dry) when you 
grasp the touch-sensitive handrail grips. 

SmartRate

®

 Features

When you begin an exercise session, a blinking 
segment in the SmartRate display appears if you 
entered your age during the setup phase. The blinking 
segment indicates the current zone of your heart rate. 

The calculation used for the heart rate target zone is 
your maximum aerobic heart rate: 
(220 minus your age) multiplied by a percent. 

For the ideal weight loss range, your heart rate should 
remain between 55% and 70% of your maximum 
aerobic heart rate. To improve your overall 
cardiovascular and respiratory fitness level, maintain 
your heart rate between 70% and 85% of your 
maximum aerobic heart rate. 

For the greatest benefits, maintain your heart rate in 
either zone for 30 minutes or more at least three times 
a week.

CAUTION: Your heart rate should never exceed 
85% of your maximum aerobic heart rate or go 
above your target zone (Diagram D).

Diagram D

Cool Down After Your Workout

Cooling down is an important aspect of your workout 
because it helps reduce muscle stiffness and 
soreness by transporting excess lactic acid out of the 
working muscles. Cooling down for at least three 
minutes helps provide a smooth transition that allows 
your heart rate to return to its normal, non-exercising 
state.

Diagram A

Diagram B

Diagram C

20 25 30 35 40 45 50 55 60 65 70 75

70

80

90

100

120

130

140

150

160

170

180

190

200

110

Heart Rate Target Zones

Your Age

Y

o

u

r Hea

rt R

a

te

Peak

Cardio

Warmup

Reco

mmen

ded C

ardio

vascu

lar Zo

ne

Recom

mende

d Weig

ht Loss

 Zone

Fatburn

High

Precor Incorporated

20031 142nd Avenue NE

P.O. Box 7202

Woodinville, WA USA 98072-4002

www.precor.com

HR INFO 48140-104

©2007

 

Precor Incorporated

Diagram D: Heart Rate Target Zones

Your Age

20  25  30  35  40  45  55  60  65  70  75

High

Peak
Cardio

Fat Burn

Warmup

200

190
180

170

160
150
140
130
120

110

100

90
80

70

Your Hear

t R

at

e

20 25 30 35 40 45 50 55 60 65 70 75

70

80

90

100

120

130

140

150

160

170

180

190

200

110

Heart Rate Target Zones

Your Age

Yo

ur

 Heart Rate

Peak

Cardio

Warmup

Reco

mmen

ded

 

Cardio

vascu

lar

 

Zone

Recom

mende

d

 

Weigh

t

 

Loss

 

Zone

Fatburn

High

heart

 ra

te

 in

Forma

tion

WELC

OME TO A 

PERSONALIZED FITNESS EXPERIENCE

 FOR Y

OUR HOME

Quick 

Start

 

Card

ENERGY

 SERIES

TRM 211 TREADMILL

CAUTION:

 

Before beginning any fitness program, see your physician for a thorough examination. Ask your physician about the appropriate target heart rate for your fitness level.

Summary of Contents for TRM 211
















































































Reviews: