background image

SPECIFICATIONS

Frequency

20hz-20kHz

Signal-to-Noise Ratio

>85dB

Separation

65dB @ 1kHz

Crossover Slope

24dB/octave

Input Impedance

20,000 Ohms

Input Sensitivity

variable, 300mV to 3V peak to peak

Output Level

variable, 300mV to 5V peak to peak

Supply Voltage

9 to 16 VDC

INSTALLATION/MOUNTING

NOTE: As an option, before beginning, disconnect the
negative (-) terminal of the battery to prevent an
electrical short to ground. Reconnect the negative
terminal only after all connections have been made.

To prevent damage to the 

MaxxBass

®

Processor while driving,

mount in a secure place. Choosing the appropriate location will
depend upon your vehicle and the complexity of your system design.
Typical mounting locations include the trunk and passenger
compartment (floor or under seat). Never mount the 

MaxxBass

®

Processor in a location that would subject it to immersion or
exposure to water.

Once a location has been chosen, securely mount the 

MaxxBass

®

Processor with the four mounting screws. Be Careful! Inspect the
area underneath to be sure you are not drilling into wires, brake or
fuel lines, etc. that could be damaged by the drill bits or screws.

7

Summary of Contents for Maxx Bass


















Reviews: