PRECISION DIGITAL Helios PD2-6200, Instruction Manual

Page: 10 / 53

Helios PD2-6200 Analog Input Flow Rate/Totalizer
Instruction Manual
10
Process Input
Inputs Field selectable: 0-20 mA, 4-20 mA

10 V (0-5 V, 1-5 V, 0-10 V)
Modbus PV (Slave)
Isolated
Transmitter
Power Supply
Terminals P+ & P-: 24 VDC

10%.
All models selectable for 24, 10, or 5 VDC
supply (Switch labeled P+/P-). 85-265 VAC
models rated @ 200 mA max, 12-24 VDC
powered models rated @ 100 mA max.
5 & 10 VDC supply rated @ 50 mA max.
Refer to
Transmitter Supply Voltage
Selection (P+, P-) on page 17 and
Figure 25. 4-20 mA Output Connections on
page 22 .
When the Light / Horn is powered by the
transmitter power supply, see MOD-PD2LH
Light / Horn's transmitter power supply
specification in MOD-PD2LH manual for
additional details. Light / Horn power not
available for 5 or 10 VDC supplies.
Accuracy ±0.03% of calibrated span ±1 count,
square root & programmable exponent
accuracy range: 10-100% of calibrated
span
Temperature
Drift
0.005% of calibrated span/

C max from
0 to 65

C ambient, 0.01% of calibrated
span/

C max from -40 to 0

C ambient
Input Signal
Conditioning Linear, square root, programmable
exponent, or round horizontal tank volume
calculation
Multi-Point
Linearization 2 to 32 points
Programmable
Exponent User selectable from 1.0001 to 2.9999 for
open channel flow
Round
Horizontal
Tank Diameter & Length: 999.999 inch or cm
calculates volume in gallons or liters
respectively.
Low-Flow
Cutoff 0.1 to 999,999 (0 disables cutoff function).
Point below at which display always shows
zero.
Decimal Point Up to five decimal places or none:
d.ddddd
,
d.dddd
,
d.ddd
,
d.dd
,
d.d
, or
dddddd
Calibration
Range
Input Range
Minimum Span
Input 1 & Input 2
4-20 mA 0.15 mA

10 V
0.10 V
An error message will appear if the input 1
and input 2 signals are too close together.
Input
Impedance
Voltage ranges: greater than 500 k

Current ranges: 50 - 100

(depending on
internal resettable fuse impedance)
Input
Overload Current input protected by an internal
resettable fuse, 30 VDC max. Fuse resets
automatically after fault is removed.
HART
Transparency The meter does not interfere with existing
HART communications; it displays the
4-20 mA primary variable and it allows the
HART communications to pass through
without interruption. The meter is not
affected if a HART communicator is
connected to the loop. The meter does not
display secondary HART variables.
Rate/Totalizer
Rate Display
Indication
-99999 to 999999, lead zero blanking.
“R” LED illuminates while displaying rate.
Total Display
& Total
Overflow 0 to 999,999; automatic lead zero blanking.
“T” LED is illuminated while displaying total
or grand total.
Up to 999,999,999 with total-overflow
feature. “
oF
” is displayed to the left of total
overflow and
▲ LED is illuminated.
Total
Decimal Point Up to five decimal places or none:
d.ddddd
,
d.dddd
,
d.ddd
,
d.dd
,
d.d
, or
dddddd
Total decimal point is independent of rate
decimal point.
Totalizer Calculates total based on rate and field
programmable multiplier to display total in
engineering units. Time base must be
selected according to the time units in
which the rate is displayed.
Totalizer
Rollover Totalizer rolls over when display exceeds
999,999,999. Relay status reflects display.
Total
Overflow
Override Program total reset for automatic with
0.1 second delay and set point 1 for
999,999
Totalizer
Presets Four, user selectable under setup menu.
Any set point can be assigned to total and
may be programmed anywhere in the
range of the meter for total alarm
indication.
Programmable
Delay
On Release 0.1 and 999.9 seconds; applied to the first
relay assigned to total or grand total.
If the meter is programmed to reset total to
zero automatically when the preset is
reached, then a delay will occur before the
total is reset.
Total Reset User selectable via front panel button, F4
terminal at back of meter, external contact
closure on digital inputs, automatically via
user selectable preset value and time
delay, or through serial communications.
Total Reset
Password Total and grand total passwords may be
entered to prevent resetting the total or
grand total from the front panel.
Non-Resettable
Total The grand total can be programmed as a
non-resettable total by entering the
password “050873”.
•
Once the Grand Total has been programmed as
“non-resettable” the feature
CANNOT be
disabled.