Precision Digital Corporation ExSense Series Instruction Manual Download Page 20 | Manualshive

Page: 20 / 36

background image

PD301 - PD306 Smart Temp Transmitters

Instruction Manual

20

SETUP AND PROGRAMMING

HART communication requires a minimum of 250

Ω

in

the 4-20 mA loop. See Load Impedance specification to
calculate the maximum load based on the power supply
voltage (e.g. 650

Ω

@ 24 VDC).

The HART signal can be accessed using a HART
communicator or a HART modem anywhere in the loop.

Overview

There are no jumpers, switches, or potentiometers involved in the
setup process of the smart temperature transmitter.

All setup and programming can be performed by one of these
methods:

1. USB modem and PC running the free software provided

2. Using a HART modem and a PC running the free software

provided

3. Using a HART Communicator (not all parameters are available)

Note: Input Type and Units cannot be changed with a HART

Communicator.

It is recommended to commission the smart temperature transmitter
prior to installation in a hazardous area.

After all connections have been completed and verified, apply power
to the temperature transmitter.

«
...
18
19
20
21
22
...
»

Summary of Contents for ExSense Series





































Reviews:

No comments

Related manuals for ExSense Series

Brand: Cooper Pages: 120

Efector 800 VTV122

Brand: IFM Electronic Pages: 5

Brand: Lathem Pages: 7

Brand: gefran Pages: 8

Brand: Micrel Pages: 47

FT-2400H-2 - SERVICE

Brand: Yaesu Pages: 14

Brand: Icom Pages: 40

Brand: Icom Pages: 60

Brand: Icom Pages: 96

Brand: Icom Pages: 17

Brand: Icom Pages: 64

Brand: Icom Pages: 16

Brand: Midland Pages: 32

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 151

Brand: IFM Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands