background image

Ether232

Plus

 User Guide

 6 

System 

Settings

02-CML000057

Precidia Technologies Inc.

53

The Com Port portion of the test will always return “

Com Port... skipped (external 

loopback not found)

” if you are running the Self Test from a local connection and do 

not have an external loopback dongle attached to the 

COM

 port. You must attach a 

loopback dongle and run the Self Test remotely via telnet to test the com port.

Messages that may result from the Com Port test are described in Table 6.1.

6.8

Reset Unit

Reset Unit is useful for troubleshooting, since it allows you to ensure that modem 
connections are dropped correctly. Reset Unit resets the Ether232

Plus

, and drops all 

active modem connections. The Configuration screen is not changed nor is the System 
Log cleared, however, the message “===== Ether232Plus Started =====” is appended 
to the System Log.

Reset Unit allows you to reset the Ether232

Plus

 from a telnet session without saving 

any changes to the configuration menu. 

6.9 SNTP Settings

Simple Network Time Protocol (SNTP) is used to synchronize computer clocks on the 
Internet. Every 5 minutes, a request is sent to the 

Primary Server

. If a response has 

not been received by the unit within one minute, a request is sent to both the 

Primary 

Server

, and the 

Secondary Server

 (if defined). This feature is disabled if the Primary 

IP address is not defined.

The real-time clock timestamp can be viewed in the System Log. Please refer to 
section 7.2 System Log for further information.

Table 6.1: Com Port Self Test Results

Result

Meaning

Com Port... passed

Everything is fine

Com Port... character not received

A transmitted character was not received

Com Port... character not transmitted

The internal port could not transmit

Com Port... skipped (external loop-

back not found)

No loopback dongle found

Com Port... control lines not looped 

back

The DTR/DSR, DTR/DCD lines, if 
present, are not looped back as expected

Com Port... transmitted and received 

characters are different

The data sent is not the same as the data 
received

Summary of Contents for Ether232Plus

































































































Reviews: