background image

 

IT 

NOTE 2:

 After turning off the UPS, please be aware that the UPS is working at Bypass mode and 

there is risk of power loss for connected devices.   

2)  In Bypass mode, output voltage of the UPS is still present. In order to cut off the output, switch off 

the line input breaker(for dual input unit, also switch off the bypass line breaker). A few seconds 

later, there is no display shown on the display panel and UPS is complete off. 

8. Turn off the UPS without utility power supply in Battery mode 

1)  Turn off the UPS by pressing “OFF” button for at least 0.5s, and then the buzzer will beep once. 
2)  Then UPS will cut off power to output and there is no display shown on the display panel. 

9. Mute the buzzer 

1)    To mute the buzzer, please press the “Mute” button for at least 0.5s. If you press it again after the 

buzzer is muted, the buzzer will beep again. 

2)  Some warning alarms can’t be muted unless the error is fixed. Please refer to section 3-3 for the 

details.   

10. Operation in warning status 

1)  When Fault LED flashes and the buzzer beeps once every second, it means that there are some 

problems for UPS operation. Users can get the warning indicator from LCD panel. Please check the 

trouble shooting table in chapter 4 for details.   

2)  Some warning alarms can’t be muted unless the error is fixed. Please refer to section 3-3 for the 

details. 

11. Operation in Fault mode 

1)    When Fault LED illuminates and the buzzer beeps continuously, it means that there is a fatal error in 

the UPS.    Users can get the fault code from display panel. Please check the trouble shooting table 

in chapter 4 for details. 

2)    Please check the loads, wiring, ventilation, utility, battery and so on after the fault occurs. Don’t try 

to turn on the UPS again before solving the problems. If the problems can’t be fixed, please contact 

the distributor or service people immediately. 

3)  For emergency case, please cut off the connection from utility, external battery, and output 

immediately to avoid more risk or danger. 

12. Operation of changing battery numbers 

1)    This operation is only available for professional or qualified technicians. 
2)  Turn off the UPS. If the load couldn’t be cut off, you should remove the cover of maintenance 

bypass switch on the rear panel and turn the maintenance switch to “BPS” position first. 

3)    Switch off the line input breaker(for dual input unit, also switch off the bypass input breaker), and 

switch off the battery breaker (only available for long-run model).   

4)  Remove  the cabinet  cover,  and  disconnect battery wire for standard model. Then  modify the 

jumper of JS3 on the control board to set the battery numbers as following table.   

 

 
 
 
 

 
Note:1 = connect with jumper; 0 = no jumper; x = the pins are for other functions.

 

5)

 

Modify the battery pack for the setting number carefully. After complete it, put the cover back, 

switch on the battery breaker for long-run model. 

Battery Number 

in series 

JS3 

pin1 

&

 pin2 

pin3 

&

 pin4 

Pin5 

&

 pin6 

pin7 

&

 pin8 

18 

19 

20 

Summary of Contents for 10000







































Reviews: