manualshive.com logo in svg

Powertronix Alcor, User Manual

Share
Download
Powertronix Alcor User Manual Download Page 28

Powertronix spa reserves the right to modify this document without notice

Page 28 of 46

R&D – USER MANUAL DT0430-E04

3.2.1.

MENU 1: UPS STATUS AND ALARMS

This menu is characterized by the first line of the message which can be UPS OPERATING (if the UPS
is operating normally) or UPS ALARM (if the UPS has an alarm condition). The meanings of the displayed
messages are given below:

UPS IN NORMAL OPERATING CONDITIONS

MESSAGE

MEANING

MAINS OK / NOT AVAILABLE

The input mains line is on and the voltage is / is not
in the specified range

RESERVE MAINS OK / NOT AVAILABLE

The input by-pass supply line is on and the voltage
is / is not in the specified range

BATTERY FLOAT CHARGE

The battery voltage is within the specified limits

INVERTER ON

The inverter is on and operating normally

INVERTER – RESERVE SYNCHRONIZED / NOT
SYNCHRONIZED

Indicates the normal synchronization status
between the inverter and by-pass line

LOAD ON INVERTER

The load is supplied by the inverter

LOAD ON RESERVE

The load is supplied by the by-pass line. This may
be  a  temporary  condition  which  lasts  20  seconds
after short overload

UPS MASTER

Controls the other UPSes in parallel system

UPS SLAVE

Controlled by another UPS in parallel system

Table 3.2.1

Summary of Contents for Alcor















































Reviews:

No comments

Brands by name

Popular brands

Load more brands