background image

Model No. ACD039

Positive Grounded System:  

Connect the BLACK CLAMP (negative -) to the negative terminal of the vehicle battery. 

Connect the RED CLAMP (po) to the vehicle engine block, or a metal part of the vehicle which 
is connected to the vehicle ground system. Do not clamp directly to positive battery terminal, main fuel 
distribution module or sheet metal parts. 

The Polarity Protection System GREEN LED is illuminated if the proper connections have been made. 

WARNING: If RED LED is illuminated, STOP and disconnect the booster clamps from battery 
terminals.  Reconnect  the  booster  clamps  by  reversing  the  connections  to  the  proper  battery 
polarity. 

1.  Turn on the Main Power Booster Clamps Switch by rotating the switch to the ON position.   
2.  Allow 3 to 5 minutes of charge time. It is highly recommended having a second person to assist 

 

 

holding the unit securely in place during the next steps. 

3.  Start the engine and Stop if the vehicle does not start after 2 to 3 seconds of engine cranking. Wait  

 

 

2 to 3 minutes then try again. Repeat the above steps several times until the vehicle starts.  

4.  If the vehicle starts, turn off the Main Power Switch by turning the switch to the OFF position. 
5.  Disconnect the clamps as far away from the vehicle battery as possible. 
6.  For Negative Grounded System, disconnect the BLACK CLAMP Negative first and then the RED 

 

 

CLAMP Positive. For Positive Grounded System, disconnect the RED CLAMP Positive first, and  

 

 

then the BLACK CLAMP Negative.      

7.  Stow the booster clamps into their storage compartment.   

 CHARGING INSTRUCTIONS:

 USE CAUTION:

Prior to charging this device read all the related instructions   indicated below. This product may arrive 
partially charged from the factory. It is highly recommended to fully charge the unit after purchase and 
before initial use:

 

• 

Make certain that the Power Switch is set to the off position.

• 

Do  not  charge  near  flammable  material,  open  flames  or  any  location  which  may  accumulate

 

 

flammable fumes. 

• 

Make certain that any electrical outlet used to charge this device that is located in a potentially wet 

 

 

or moist area is protected by a Ground Fault Circuit Interrupter (GFCI). 

• 

Make sure that both booster clamps are securely placed in their designated storage compartments 

 

 

when not in use and during the charging period.

Sheet

 6

 of

 8

Summary of Contents for PowerBeam ACD039









Reviews: