background image

2.2.2 CLOSE DELAY OF DUAL GATE OPERATION ADJUSTMENT (DIP 3.DELAY1, DIP 4.DELAY2)

Close/Open delay of two leaves of gate can be adjusted from 2 to 6 seconds

OFF

ON

OFF

ON

Dip3. Delay 1                           Dip4. Delay 2

OFF
OFF

ON
ON

2 sec
2 sec
3 sec
3 sec

3 sec
4 sec
5 sec
6 sec

DIP switch

Open Delay

Close Delay

2.2.5 OPERATION SPEED ADJUSTMENT OF THE GEAR MOTORS (DIP 7.O SPEED)

ON: The speed is 100% output of the full speed. 
OFF: The speed is 70% output of the full speed.

2.2.6 SINGLE AND DUAL GATE OPERATION ADJUSTMENT (DIP 8.DS/SET)

ON: Dual Gates operation in system learning and normal operation. 
OFF: Single Gate operation in system learning and normal operation.

2.2.3 ELECTRIC LATCH ADJUSTMENT (DIP 5.LATCH)

ON: The master leaf will move toward closing direction for 0.25 second once command the remote, then unlock the 
        latch to open the gate.
OFF:   Once command the remote, the the latch will be unlocked to open the gate immediately

2.2.4 DECELARATION SPEED ADJUSTMENT OF THE GEAR MOTORS (DIP 6. D SPEED)

ON: The speed is 70% output of the full speed. 
OFF: The speed is 50% output of the full speed.

2.3 LED INDICATION

LED1  System Learning:

 LED1 is always ON when the system learning in not completed.

                                           LED1 blinks once when single-gate learning is completed ; 
                                          LED1 blinks twice when dual-gate learning is completed.

LED2  RF : 

If the switch of the transmitter, key selector, or the push button is activated, LED2 will be on.

LED3  Photocells 1 : 

LED3 will be on when the first pair of the photocells are activated. 

LED4  Photocells 2 : 

LED4 will be on when the second pair of the photocells are activated. 

LED5  RF Indicator : 

LED5 will be on when RF signal is received.

Antenna

LED1

LED2

LED3

LED4

LED1

LED2

LED3

LED4

SYSlearn

RFLED

Ph01

Ph02

CONTROL BOX

5

Summary of Contents for PC170













Reviews: