powersoft Duecanali 1604 Service Manual Download Page 50 | Manualshive

Page: 50 / 68

background image

50

13. Updating of the Firmware using ArmonìaPlus 1.3

On the bottom of the Armonia Workspace panel, click on
“Match” & on the top panel, click on “Discovery” in order
to load the unit.

This procedure may take up to 5 seconds.

Once properly loaded, the Amplifier and its Serial Number
should appear on the window.

By hovering the Mouse onto the unit, the following
information will be displayed.

EXAMPLE:
Model: Quattrocanali D
Serial: 00506652
Device Address: 169.254.9.71
Firmware:

1.7.6.74

(OLD VERSION)

Click on “System List”.

Check on the amplifier required to Update Firmware.

Click on the “Update Selected”.

Upon clicking the “Update Selected”, the installation of Firmware begins.

After completed the updating, Armonia will show the latest firmware of the Amplifier.

Firmware:

1.8.7.16

(NEW VERSION)

QUATTROCANALI | SERVICE MANUAL

«
...
48
49
50
51
52
...
»

Summary of Contents for Duecanali 1604





































































Reviews:

No comments

Related manuals for Duecanali 1604

Brand: Bad Cat Pages: 9

Brand: E&I Pages: 13

Brand: Fender Pages: 32

Brand: Fender Pages: 4

Hot Rod DeVille

Brand: Fender Pages: 2

Brand: Fender Pages: 12

Brand: Fender Pages: 16

Blues Deluxe Reissue

Brand: Fender Pages: 16

Acoustasonic SFX

Brand: Fender Pages: 20

Acoustasonic 30

Brand: Fender Pages: 8

Bassman Bassman 100

Brand: Fender Pages: 16

Bassman Bassman 100

Brand: Fender Pages: 4

Brand: Fender Pages: 20

Brand: Fender Pages: 20

Brand: Fender Pages: 4

65 Deluxe Reverb

Brand: Fender Pages: 12

Brand: Fender Pages: 2

Brand: Fender Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands