Powerplus POWXG50200 Quick Start Manual Download

Page: 13 / 15

POWXG50200

P a g e

www.varo.com

- Pull the recoil starter handle three to four times to distribute the oil along the cylinder
bore, then refit the spark plug.

▪

Store in a dry place away from sources of ignition.

▪

Do not stack items on top of the grass trimmer.

14 TECHNICAL DATA

Cylinder capacity

31 cc

Engine power

0.8kW

Clutch engagement speed

4500 min

-1

Idle speed

3000 min

-1

Engine stroke type

4 stroke

Engine brand

Powerplus

Oil tank capacity

0.06 l

Fuel tank capacity

0.24 l

Choke type

Automatic switch off

Easy start engine

Yes

Horse power

1.13 hp

Full crank engine

Yes

Carburettor type

HUAYIN

Spark plug type

NSTAM5RC

Safety guard

Yes

Handle type

Bike handle

Shaft type

Straight

E10 fuel proof

Yes

Shaft length

1333.8 mm

Brush cutter

Cutting width

255 mm

Rotation speed

5700min

-1

Size of blade

255x25,4x1.4 mm

– 3T

Grass trimmer

Cutting width grass trimmer

450

Rotation speed grass trimmer

5700 min

-1

Thread lengthening type

Tap&Go

Spool thread diameter

2,5 mm

Spool thread length

5 m

Double thread

Yes

15 NOISE

Noise emission values measured according to relevant standard. (K=3)

Acoustic pressure level LpA

84 dB(A)

Acoustic power level LwA

113 dB(A)

ATTENTION! Wear hearing protection when sound pressure is over 85
dB(A).

aw (Vibration)

10.5m/s²

K = 1.5 m/s²

Summary of Contents for POWXG50200
















Search results

Summary of Contents for POWXG50200

Reviews:

Related manuals for POWXG50200

Brands by name

Popular brands

Powerplus POWXG50200, Quick Start Manual

Search results

Summary of Contents for POWXG50200

Reviews:

Related manuals for POWXG50200

Brands by name

Popular brands