background image

 

POWXG50200 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

5

 

www.varo.com 

 

In start-up or during operation of the engine, never touch hot parts such as the muffler, the 
high voltage wire or the spark plug. 

 

After the engine has stopped, the muffler is still hot. Never place the machine in any 
places where there are flammable materials (dry grass, etc.), combustible gasses or 
combustible liquids. 

 

Pay special attention to operation in the rain or just after the rain as the ground may be 
slippery. 

 

If you slip or fall to the ground or into a hole, release the throttle lever immediately. 

6  SPECIFIC SAFETY WARNINGS 

 

BLADE CAN RECOIL VIOLENTLY FROM MATERIAL IT CANNOT CUT 

– Blade can 

cause you to lose arms or legs.  Keep people and animals 30 feet (10 meters) away in all 
directions. If blade contacts foreign objects during operation, turn off engine and allow 
blade to come to a halt. Then check blade for damage. Always discard blade if it is warped 
or cracked. 

 

BLADE CATAPULTS OBJECTS THROUGH AIR - You can be blinded or injured. Wear 
eye, face, and leg protection.  Always clear work area of any foreign objects before using 
blade. Keep people and animals 10 metres away in all directions. 

 

BLADE COASTS AFTER THROTTLE IS RELEASED - A coasting blade can injure you or 
bystanders. Before servicing the blade, always turn off engine, and be sure coasting blade 
has stopped.  

 

WARNING DO NOT USE ANY OTHER FUEL than that recommended in your manual. 
Always follow instructions in the Fuel and Lubrication section of this manual. Never use 
petrol unless it is properly mixed with 2-cycle engine lubricant. Permanent damage to 
engine will result, voiding manufacturer’s warranty. 

 

DO NOT USE ANY OTHER CUTTING ATTACHMENT. Only use our replacement parts 
and accessories, which are designed specifically to enhance the performance and 
maximize the safe operation of our products. Failure to do so may cause poor 
performance and possible injury. Use only the stringhead supplied with this product. Do 
not use any other cutting attachment. Use of such attachments will void your factory 
warranty and may result in serious bodily injury. 

7  SAFETY WARNINGS GASOLINE 

WARNING:  Use  extra  care  in  handling  fuels.  They  are  flammable  and  the 
vapours are explosive. The following points must be observed. 

 

Use only an approved container. 

 

Never remove the fuel cap or add fuel with the power source running. Allow engine 
exhaust components to cool before refuelling. 

 

Do not smoke. 

 

Never refuel the machine indoors. 

 

Never store the machine or fuel containers inside, where is an open flame, such as a 
water heater. 

 

If fuel is spilled, do not attempt to start the power source, but move the machine away 
from the area of spillage before starting. 

 

Always replace and securely tighten the fuel cap after refuelling. 

 

If the tank is drained, this should be done outdoors. 

Summary of Contents for POWXG50200
















Reviews: