background image

 

POWXG30412 

EN

 

Copyright © 2020 VARO 

P a g e

 | 

14

 

www.varo.com 

16 TROUBLE SHOOTING 

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

Unit won’t start or 
starts but will not run. 

 

Incorrect starting 
procedures. 

 

Incorrect carburettor 
mixture adjustment 
setting. 

 

Fouled sparking plug. 

 

Empty fuel tank. 

 

 

Primer bulb was not 
pressed enough. 

 

Follow instructions in the User 
Manual. 

 

Have carburettor adjusted by 
an Authorized Service Centre. 

 

 

Clean/gap or replace plug. 

 

Fill fuel tank with properly 
mixed fuel. 

 

Press primer bulb fully and 
slowly 10 times. 

Unit starts, but 
engine has low 
power. 

 

Fuel filter is plugged. 

 

Incorrect lever position. 

 

Dirty spark arrester 
screen. 

 

Dirty air filter. 

 

 

Incorrect carburettor 
mixture adjustment 
setting service dealer. 

 

Replace the fuel filter. 

 

Move to RUN position. 

 

Replace spark arrester screen. 

 

 

Remove, clean and reinstall 
filter. 

 

Have carburettor adjusted by 
an Authorized Service Centre. 

Engine sputters. 

 

Incorrect carburettor 
mixture adjustment 
setting. 

 

Air filter is blocked. 

 

Old or improperly mixed 
fuel. 

 

Have carburettor adjusted by 
an Authorized Service Centre. 

 

 

Replace or clean the air filter. 

 

Drain gas tank/add fresh fuel 
mixture. 

No power under load. 

 

Incorrect carburettor 
mixture adjustment 
setting. 

 

Old or improperly mixed 
fuel. 

 

Air filter is blocked. 

 

Fouled sparking plug. 

 

Have carburettor adjusted by 
an Authorized Service Centre. 

 

 

Drain gas tank /add fresh fuel 
mixture. 

 

Replace or clean the air filter. 

 

Clean/gap or replace plug. 

Runs erratically. 

 

Incorrectly gapped 
sparking plug. 

 

Blocked spark arrester. 

 

Dirty air filter. 

 

Clean/gap or replace plug. 

 

 

Clean or replace spark arrester. 

 

Clean or replace air filter. 

Smokes excessively. 

 

Incorrect carburettor 
mixture adjustment 
setting. 

 

Incorrect fuel mixture. 

 

Have carburettor adjusted by 
an Authorized Service Centre. 

 

 

Use properly mixed fuel (40:1 
mixture). 

 

 

Summary of Contents for POWXG30412

















Reviews: