background image

 

POWXG30412 

EN

 

Copyright © 2020 VARO 

P a g e

 | 

11

 

www.varo.com 

10.6 

Cutting with blades 

AVOID KICKOUT 
Kickout refers to the reaction of a moving blade if it contacts a strong tree, brush or a solid 
object. The force that results violently pushes the blade away in an arc. Kickout may cause 
loss of control resulting in injury to the operator or bystanders. 
Do not use a blade near a chain link fence, metal stakes, landscape borders or building 
foundations. 

Do not cut with dull, cracked or damaged metal blade. Before cutting growth, 
inspect  for  obstructions  such  as  boulders,  metal  stakes  or  strands  of  wire 
from  broken  fences.  If  an  obstruction  can  not  be  removed,  mark  its  location 
so that you can avoid it with the blade. Rocks and metal will dull or damage a 
blade. Wire can catch on the blade head and flap around or be thrown into the 
air. 

Do not use a brush cutter for cutting trees. 

11 MAINTENANCE 

11.1 

Air filter 

CAUTION: NEVER operate trimmer without the air filter or dust and dirt will be 
sucked  into  the  engine  and  damage  it.  The  air  filter  must  be  kept  clean.  If  it 
becomes damaged, install a new filter. 

 

Accumulated dust in the air filter will reduce engine efficiency, increase fuel consumption 
and allow abrasive particles to pass into the engine. Remove the air filter as often as 
necessary to maintain in a clean condition. 

 

Light surface dust can readily be removed by tapping the filter. Heavy deposits should be 
washed out in soap water. 

 

Remove filter cover by loosening air filter cover knob. 

NOTE: Replace filter if frayed, torn, damaged or if it cannot be cleaned. 

11.2 

Fuel cap / fuel filter 

CAUTION:  Remove  fuel  from  unit  and  store  in  approved  container  before 
starting  this  procedure.  Open  fuel  cap  slowly  to  release  any  pressure  which 
may have formed in fuel tank. 

Keep vent on fuel cap free of debris. 

 

Lift fuel line and filter out of tank. A steel wire with a hook or a paper clip works well. 

 

Pull off fuel filter with a twisting motion. 

 

Replace the fuel filter. 

NOTE:  Never  operate  the  tool  without  the  fuel  filter.  Internal  engine  damage 
could result and / or disturb a good operation. 

When the inside of the fuel tank is dirty, it can be cleaned by rinsing the tank 
out with gasoline. 

Summary of Contents for POWXG30412

















Reviews: