6.9.1 Replace Cylinder Broom V-
Belt
- Turn engine off and pull key.
- Secure machine by engaging
parking brake.
- Disconnect battery plug
- Detent tensioning spring (Fig.
24/10) by left hand while taking the
V-belt off the tensioning roller with
right hand.
- Remove V-belt (Fig. 24/7).
Proceed in inverse order for moun-
ting.
6.9.2 Replace Side Brush V-Belt
- Turn engine off and pull key.
- Secure machine by engaging par-
king brake
- Disconnect battery plug
- Remove bottom right cover (turn
locks counter-clockwise by square
spanner).
- Remove cylinder broom V-belt (as
described in paragraph "Replace
Cylinder Broom V-Belt")
- Loosen screws (Fig. 24/13) at the
cover plate and remove
- Remove cover plate
- Push side brush from the front side
in direction of the machine to detent
V-belt (Fig. 24/5)
- Remove V-belt (Fig. 24/5)
Proceed in inverse order for moun-
ting.
6.9.3 Replace Suction Fan V-Belt
- Turn engine off and pull key.
- Secure machine by engaging par-
king brake
- Open seat hood
- Disconnect battery plug
- Open quick-release locks (Fig.21/1)
- Remove filter case cover (Fig.21/3)
- Loosen screws at the inside of the
right lateral fairing and remove.
- Tilt lateral fairing lightly to the outsi-
de, the remove by pulling upwards.
- Loosen tensioning roller (Fig. 24/1)
- Loosen hexagonal nuts (Fig. 24/11)
and hexagon socket screw
(Fig.24/12).and detent V-belt
(Fig.24/4)
- Remove V-belt (Fig.24/4) from V-
belt pulley (Fig.24/3).
- Remove V-belt (Fig.24/2).
Proceed in inverse order for moun-
ting. Do not exceed tension of V-belt.
Observe the following when
mounting the V-belt: First
adjust tension of V-belt
(fig.24/4), then adjust ten-
sion of V-belt (fig.24/2).
6.10 Adjust Steering Chain Tension
Check the condition and function of
steering chain every 200 hours of
operation.
Proceed to adjustment of tension via
a spring located in the pedal area
and accessible after removal of the
cover plate.
We recommend having this adjust-
ment work done by qualified person-
nel only.
Adjust tension of the stee-
ring chain such that rotatio-
nal movement is possible
without jerks.
6.11 Check Hydraulic Fluid and
Refill
6.11.1 Check Hydraulic Fluid
- Turn engine off and pull key
- Secure machine by engaging par-
king brake
- Open seat hood
- Check hydraulic fluid level at tank
(Fig. 25/1), the level must not fall
below the minimum mark (Fig.
25/2). It should read between mini-
mum (Fig. 25/2) and maximum
mark (Fig. 25/3).
6.11.2 Refill Hydraulic Fluid
- Remove cover (Fig. 24/4) and refill
hydraulic fluid
- Close hydraulic fluid tank with cover
Use DTE 15M hydraulic fluid or a
fluid of similar quality.
Maintenance/Service
Fig.25
42
Summary of Contents for SW5X
