background image

 PowerBoss, Inc. Copyright 2010

PB# 4100039  Rev.* 06/10

Armadillo 9X Series Sweeper                                                                         

 

Page  16

Air Filter Element Removal

1.  Turn off the engine and set the parking brake.
2.  Lift the engine cover.
3.  Locate the air filter and loosen the retaining 

clamp.

NOTE:  The diesel engine has a screw type 

retaining clamp. The gas and LP engines 

have two lever retaining clamps.

4.  Remove the dust cup.
5.  Pull the rubber plug out of the dust cup and 

empty the contents.

NOTE:  The Diesel engine has a wing nut holding the 

air filter element in place, remove the wing nut  

first.

6.  Pull the air filter elements out of its housing.

Air Filter Cleaning

1.  Once you have removed the air filter 

elements, empty the dust cup and clean the 

interior of  the air filter housing.

2.  Use an air hose to blow out the air filter 

elements. Air pressure should be 100 psi or 

less.

Air Filter Inspection

1.  After you clean the air filter elements, check 

the elements for holes by passing a light bulb 

inside it.

Air Filter Installation

1.  Wipe out the air cleaner housing with a damp 

cloth. Be sure all dirt is removed.

2.  Install the cleaned replacement filter elements 

so that the fins are at the far end of the  

 

housing. Be careful not to damage the fins.

3.  Replace the wing nut and tighten it (Diesel 

only).

4.  Replace the rubber plug in the dust cup.
5.  Replace dust cup, being sure embossed word 

“top” on cup is positioned correctly    

(up).

6.  Tighten the ring clamp or retaining clips.
7.  Check the condition of intake hoses and 

clamps. Close engine cover.

TROUBLESHOOTING PROCEDURES

AIR INTAKE SYSTEM
Check Air Filter Service Indicator

The air filter service indicator shows when to 

change the air filter element. Check the indicator 

on a daily basis. The red indicator gradually 

becomes visible as the air filter elements load 

with dirt. It is not necessary to change the air filter 

elements until the red indicator reaches the top of 

the service indicator and locks into position. 
1.  Lift engine cover.
2.  Inspect air filter service indicator

NOTE:  The indicator may return to the nonviable 

position when the engine is shut off. To 

check, reset indicator and turn on the 

engine, if it locks in visible position again 

clean or change element.

AIR FILTER 

ELEMENT INNER

AIR FILTER SERVICE 

INDICATOR

RETAINING 

CLAMPS

DUST CAP

AIR FILTER 

ELEMENT OUTER

TROUBLESHOOTING AND REPAIR

Summary of Contents for 9XDLXDSLBR







































Reviews: