Poweramp LHP Series Owner & User Manual Download Page 24 | Manualshive

Page: 24 / 52

background image

22

4111-0012 — Sept. 2018

© 2018 Systems, LLC

Placard Installation Instructions

Control Box

Conduit

Nylon Tie

Placard

• Owner/Users are responsible for the installation and placement of product

placards.

• Make sure placard is in plain view of dock leveler and/or vehicle restraint

operations.

• Suggested placement of placard is near control box attached to electrical

conduit by using nylon tie. If there is no control box present, mount placard
on wall to the immediate left of leveler at eye level.

(Placard placement
shown as reference
only.)

• Owner/Users are responsible for the installation and placement of product

placards.

• Make sure placard is in plain view of dock leveler and/or vehicle restraint

operations.

• Suggested placement of placard is near control box attached to electrical

conduit by using nylon cable tie. If there is no control box present, mount placard

on wall to the immediate left of leveler at eye level.

A

B

C

D

A - Control Box

B - Placard

C - Nylon Cable Tie

D - Conduit

Placard Installation Instructions

Control Box

Conduit

Nylon Tie

Placard

• Owner/Users are responsible for the installation and placement of product

placards.

• Make sure placard is in plain view of dock leveler and/or vehicle restraint

operations.

• Suggested placement of placard is near control box attached to electrical

conduit by using nylon tie. If there is no control box present, mount placard
on wall to the immediate left of leveler at eye level.

(Placard placement
shown as reference
only.)

(Placard placement shown

as example only.)

Figure 15

INSTALLATION

«
...
22
23
24
25
26
...
»

Summary of Contents for LHP Series





















































Reviews:

No comments

Related manuals for LHP Series

Brand: Vancare Pages: 31

Brand: Jacka Industries Pages: 24

Brand: fadini Pages: 20

Brand: Sensitron Pages: 11

Brand: JAMO Pages: 18

WALLACE & TIERNAN SFC SC

Brand: Evoqua Pages: 82

Brand: Thiele Pages: 5

Brand: Spartus Pages: 28

Brand: Mitsubishi Pages: 8

Brand: Newco Pages: 32

Brand: Contec Pages: 55

Brand: NewArc Pages: 20

Brand: Jaga Pages: 8

Brand: Draper Pages: 18

DIAPERFEEDER IP54 DUOLOOP

Brand: btsr Pages: 57

Brand: Bosch Pages: 212

Brand: Honeywell Pages: 12

PEHA 940/24 EM RÜ o.T.

Brand: Honeywell Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands