manualshive.com logo in svg

Power Wheels BOSS 302 Mustang, Owner'S Manual

Share
Download
Power Wheels BOSS 302 Mustang Owner'S Manual Download Page 9

9

W9257pr-0920

ASSEMBLY

6

Note:

 

There is a right and left front wheel. They are 

marked with an R and L.
• Locate the right front wheel marked with an R. Place 

the front wheel R, onto the front axle on the right 

(passenger’s) side of the vehicle.

• Fit a wheel cover onto the right front wheel.

7

• Fit a 

3/8

"-16 (1 cm) lock nut, 

rounded side out

, onto the  

front axle.

IMPORTANT!

 Tighten the lock nut 

firmly

 with the 

assembly tool.
• Test to be sure the front wheel moves freely on the front 

axle. Turn the front wheel.

• If the front wheel does not move freely, loosen the 

lock nut 

1/4

 turn and test again. Repeat this procedure 

as necessary.

• Repeat steps 5-7 to assemble the other washer, bushing, 

front wheel and wheel cover with the remaining 

3/8

"-16 

(1 cm) lock nut on the other side of the vehicle.

Grille

9

10

• Insert six #8 x 

3/4

" (1,9 cm) screws into the front bumper  

and tighten.

• Fit the grille onto the front bumber. 
• Insert two 

black

 #8 x 

3/4

" (1,9 cm) screws into the  

grille and tighten. 

Wheel Cover

Front Wheel

(

Marked 

R)

Lock Nut

Lock Nut

Assembly 

Tool

Assembly 

Tool

FRONT VIEW

• Align the slot in a hubcap with the rib in the wheel 

cover. 

“Snap”

 a hubcap into the center of each  

wheel cover.

• Turn the vehicle upright.

8

Hubcaps

Hubcaps

Summary of Contents for BOSS 302 Mustang

























Reviews:

No comments

Brands by name

Popular brands

Load more brands