manualshive.com logo in svg

Power Wheels BOSS 302 Mustang, Owner'S Manual

Share
Download
Power Wheels BOSS 302 Mustang Owner'S Manual Download Page 13

13

W9257pr-0920

ASSEMBLY

• Insert the curved end of the steering column though 

the hole in the steering linkage. 

25

24

• Turn the vehicle over.
• Insert two #8 x 

3/4

" (1,9 cm) screws through the 

vehicle and into the rear deck. Tighten the screws.

• Insert the straight end of the steering column down 

through the hole in the vehicle floor and out through 

the hole in the dashboard.

23

BOTTOM 

BACK END VIEW

BOTTOM 

FRONT END VIEW

Steering 

Column

Steering 

Linkage

Steering 

Linkage

Steering Column

Note: 

The seat is adjustable and has three positions. 

You can move the seat back as your child grows.
• Insert both tabs on the front edge of the seat into one 

of the sets of slots inside the vehicle.

• Choose the slots closest to the dash for shorter drivers 

and the slots furthest from the dash for taller drivers.

21

TOP VIEW

• Insert three 

black

 #8 x 

3/4

" (1,9 cm) screws into the back 

of the seat and tighten.

Note: 

You will need to remove these three screws if you 

change the seat position later.

22

BACK VIEW

Summary of Contents for BOSS 302 Mustang

























Reviews:

No comments

Brands by name

Popular brands

Load more brands