background image

4

Safety Precautions

Overview of Preventive Measures

Operation Manual

Carefully read the operation manual of the saw chain. 

Be fully familiar with the operating instructions of 

the saw chain, and properly operate the saw chain. 

Personal injury may be easily caused if you do not 

follow the suggestions in the manual. If you have any 

question, please contact SURPASS product distributor.

Physical conditions

Do not operate the chain saw after drinking or 

taking narcotic drugs or when you feel tired.
In order to ensure operation safety, be sure that 

your mind and body are in good condition. Any 

improper judgment or action will result in serious 

and even fatal consequences.
If you feel uncomfortable, tense work will further deteriorate 

your health condition. Therefore, please examine your physical 

conditions before operating the chain saw. Don’t operate the 

machine if you are sick or tired or you take drugs or other food that 

will seriously affect the eyesight, action sensitivity and judgment.

Safety protection equipment

Wear appropriate goggles to protect your eyes, as wood 

chippings, dust, suddenly broken branches or other waste may 

be thrown to you in the cutting process. Goggles can also be 

used to protect your eyes to the most extent if the chain saw hits 

the face in the cutting process. If required, wear the goggles 

under the ventilating mask.
SURPASS strongly recommends the operator to wear earmuffs 

during operation of the chain saw; otherwise, your hearing will 

be affected. You must wear the “helmet” type protective device 

or earmuffs approved by the safety organization to protect your 

hearing. Any person that operates the chain saw frequently must 

receive hearing examination on a regular basis.
Wear the heat during operation of the chain saw. If you work 

under a tree or a place where there is a chance that something 

may hit you, please wear a qualified safety helmet.

You must wear heavy and non-slip labor protection gloves to 

help hold the chain saw, protect you under cold conditions and 

reduce vibration.

Wear the complete labor protection shoes or boots 

with non-slip soles. Do not wear loose clothes, 

jackets without buttons or clothes with sleeves or legs 

extended outwards. Do not wear the scarf, lacing, tie, 

bracelet, necklace and other kinds of jewelry, which 

may be easily hooked by the chain saw or branches.

Wear fitting clothes made of durable materials to prevent clothes 

from being hooked or broken. However, the flexible operation 

must be guaranteed.
Legs must be tie. Preferably, legs should be inserted into the 

labor protection boots or shortened. It is more effective to 

wear labor protection clothes, leg protection leather trousers or 

special trousers for woodcutters.
If possible, the operator should wear the above labor protection 

articles. The chain saw must be operated by more than one 

person. At least one person should be appointed to help you 

when required.

Fuel

Warning  

  Danger

•   Gasoline and oil are flammable. If gasoline or oil 

spills out or if there is a fire source, fire may be easily 

caused, resulting in serious burns and huge property 

losses. So please be very careful when adding fuel.

•   After refueling, tighten the fuel container cover and 

check whether fuel leaks. In case of leakage, repair 

the fuel container before starting the engine, so as 

to prevent fire.

Summary of Contents for PK4014




























Reviews: