manualshive.com logo in svg

Power integrations Scale-2 1SC0450E2B0, Applications Manual, Page: 2 / 25

Share
Download
Power integrations Scale-2 1SC0450E2B0 Applications Manual Download Page 2

SCALE™-2 1SC0450E2B0 

   

 

Preliminary Description & Application Manual 

 

www.power.com/igbt-driver 

Page 2 

Contents 

Driver Overview ............................................................................................................................. 4

 

Mechanical Dimensions .................................................................................................................. 5

 

Pin Designation .............................................................................................................................. 7

 

Recommended Interface Circuitry for the Primary-Side Connector .............................................. 8

 

Description of Primary-Side Interface ........................................................................................... 8

 

General ............................................................................................................................... 8

 

VCC terminal ....................................................................................................................... 8

 

VDC terminal ....................................................................................................................... 8

 

GND ................................................................................................................................... 9

 

SO (status output) ............................................................................................................... 9

 

Recommended Interface Circuitry for the Secondary Side Connectors ........................................ 9

 

Pins 6 to 16 ......................................................................................................................... 9

 

Pins 17 to 32 ..................................................................................................................... 10

 

Description of Secondary-Side Interfaces ................................................................................... 10

 

General ............................................................................................................................. 10

 

DC/DC output (VISO), emitter (VE) and COM terminals ......................................................... 11

 

Reference terminal (REF) ................................................................................................... 11

 

Collector sense (VCE) ......................................................................................................... 11

 

Input for adjusting the turn-off delay in fault condition (CSHD) ............................................. 14

 

Active Clamping (ACL) ........................................................................................................ 15

 

Gate turn-on (GH) and turn-off (GL) terminals ..................................................................... 15

 

Gate Boosting Power Supply (VGB) ..................................................................................... 16

 

Gate Boosting Signal (GBS) ................................................................................................ 16

 

Gate Drive Input (IN) ......................................................................................................... 16

 

Status Feedback /Fault input (OUT) .................................................................................... 16

 

How Do 1SC0450E2B0 SCALE-2 Drivers Work in Detail? ............................................................ 19

 

Power supply and electrical isolation ................................................................................... 19

 

Power-supply monitoring .................................................................................................... 19

 

Parallel connection of IGBT modules ................................................................................... 19

 

3-level or multilevel topologies ............................................................................................ 19

 

Gate Boosting .................................................................................................................... 20

 

Bibliography ................................................................................................................................. 22

 

The Information Source: SCALE-2 Driver Data Sheets ................................................................ 23

 

Quite Special: Customized SCALE-2 Drivers ................................................................................ 23

 

Technical Support ........................................................................................................................ 23

 

Quality .......................................................................................................................................... 23

 

Legal Disclaimer ........................................................................................................................... 23

 

Summary of Contents for Scale-2 1SC0450E2B0


























Reviews:

No comments