![background image](http://html.mh-extra.com/html/power-craft/6851/6851_user-manual-and-warranty_1586337006.webp)
2. ADJUSTING THE CUTTING ANGLE
The cutting angle can be set by unlocking the clamping knob (8} and put the
angle stop (4) in the required angle.
3. ADJUSTING THE HEIGHT
First mount the plastic base 16 over the fence.
The correct height can be set by unlocking the clamping knob 8 and turning the
height adjustment knob 9 to the desired height with the aid of the scale 10. The
height must correspond to half of the material thickness of the work piece; the
groove of the biscuit dowel must always be in the centre of the work piece.
MOUNTING ACCESSORIES
Disconnect the plug from the mains socket
1. MOUNTING THE SAW BLADE
Loosen lour screws and open the lop of the base plate
Press the spindle lock and turn the spindle (17) until it engages in the lock.
Keep the spindle lock pressed during this procedure.
Remove the flange nut (18) from The spindle using the wrench (19).
Position the saw blade (20) and the flange (21).
Place the flange nut (18) from the spindle (17) and tighten it with the wrench.
Take care that the flange nut will be placed with the correct aide on the spindle.
Release the spindle lock and check that the spindle is unlocked by rotating it.
Close the top of the base plate and fasten four screws.
Make sure that the top of the base plate is securely closed before
operating the machine
2. MOUNTING THE DUST BAG
For dust extraction the dust bag (i4) can be used. Insert the dust bag (14) into
the vacuuming Connection (13). Empty the dusts bag regularly so that the
vacuuming performance remains intact.
The biscuit jointer is suitable for cutting grooves for biscuit dowel joints in
solid wood, plywood, chipboard, fiberboard, Plexiglas and artificial marble.
It is not designed for commercial use.
ADJUSTMENTS
1. ADJUSTING THE CUTTING DEPTH
Always check the milling depth after mounting a saw blade and before first use.
Remove the plug from the socket
Move the motor base as far as possible backwards
Set the milling depth in the maximum position by turning the depth adjust-
ment knob 6.(19)
Move the motor base forwards till the pin falls into the notch of the adjust-
ment knob 6.
Turn the saw blade till one tooth of the saw blade is in the front position.
Measure the distance from the side of the base plate to the tooth of the saw
blade.
Check if the distance is 19 mm because the maximum position is (19)
If not, unscrew first the nut of the adjusting knob, then turn this adjusting
knob 15 till the distance is OK.
Afterwards lock the nut.
Then use the adjusting knob 6 to set the cutting depth.
Move the motor base forwards and check if the pin will fall into the notch of
the adjustment knob 6.
The following table shows the relationship of the markings on the adjustment
knob to cutting depth, thickness of material and associated biscuit dowel:
•
•
•
•
•
•
•
•
•
•
•
11
10
Helpline No. UK / Northern Ireland 0870 112 1948 Rep. Ireland 0800 32 929292
Web Support:
www.clickspares.co.uk
Model Number: 6851
Helpline No. UK / Northern Ireland 0870 112 1948 Rep. Ireland 0800 32 929292
Web Support:
www.clickspares.co.uk
Model Number: 6851
Application
Marking
Thickness of
material
Biscuit
dowel
Cutting depth
in mm
0
3-12mm
N°0
3.0
10
12-15mm
N°10
10
20
>15mm
N°20
12.3
M
19
•
•
•
•
•
•
•
•
•
•