background image

5

ASSEMBLY

•      Grasp handle assembly.  Hold in “up” position.  Be sure 

handle lock remains in gearcase notch.  Slide handle 
assembly into position.

HANDLE ASSEMBLY
"UP" POSITION

FIG. 4

UNPACKING CARTON (See Fig. 2)

CAUTION:  Be careful of exposed 
sta ples when handling or disposing 
of cartoning material.

IMPORTANT: 

WHEN  UN PACK ING AND AS SEM BLING TILLER, 

BE CAREFUL NOT TO STRETCH OR KINK CABLES.

•         While holding handle assembly, cut cable ties se cur ing 

handle assembly to top frame and depth stake.  Let 
handle assembly rest on tiller.

•      Remove top frame of carton.
•      Slowly ease handle assembly up and place on top of 

carton.

•      Cut down right hand front and right hand rear cor ners 

of carton, lay side carton wall down.

•      Remove packing material from handle assembly.

FIG. 2

SHIFT ROD

INSTALL HANDLE (See Figs. 3, 4, and 5)

•     Insert one handle lock (with teeth facing outward) in 

gearcase notch.  (Apply grease on smooth side of 
handle lock to aid in keeping lock in place until handle 
assembly is lowered into position.)

HANDLE
AS SEM BLY

FIG. 3

HANDLE ASSEMBLY

GEARCASE
NOTCH

HANDLE
LOCK

VIEWED FROM R.H. SIDE OF TILLER

LOOSEN HANDLE
LOCK LEVER TO MOVE

TIGHTEN HANDLE LOCK 
LEVER TO  HOLD

CARRIAGE
BOLT

SLOT

GEARCASE

HANDLE
LOCK

FLAT
WASHER

HANDLE LOCK
LEVER

PIVOT BOLT

LOCKNUT

HANDLE
BASE

FIG. 5

•         Rotate handle assembly down. Insert rear carriage bolt 

fi rst, with bolt head on L.H. side of tiller and loosely 
assemble locknut (See Fig. 5).

•      Insert pivot bolt in front part of plate and tighten.
•      Cut down remaining corners of carton and lay panels 

fl at.

•     Lower the handle assembly. Tighten nut on carriage 

bolt so handle moves with some resistance. This will 
allow for easier adjustment.

•     Place fl at washer on threaded end of handle lock le-

ver.

•     Insert handle lock lever through handle base and 

gearcase. Screw in handle lock lever just enough to 
hold lever in place.

•     Insert second handle lock (with teeth in ward) in the 

slot of the handle base (just inside of washer).

•      With  handle  assembly  in  lowest  position,  securely 

tight en handle lock lever by rotating clockwise.  Leav-
 ing handle assembly in lowest position will make it  
easier to remove tiller from carton.

Summary of Contents for PRRT65C





























Reviews: