background image

23

REPAIR PARTS

     SNOW THROWER - - MODEL NO. 

PP8527ES 

(96192001100)

CONTROL PANEL / DISCHARGE CHUTE

KEY   PART                
NO.    NO.                    DESCRIPTION

   1    183334            Knob, Lever
   2    17501010        Screw  #10-24 x 5/8
   3    179096X428    Strap, Slotted
   4    73800600        Nut, Lock  3/8-16
   5    19131316        Washer, Flat  3/8
   6    404974            Control Assembly, Chute Rotater
   7    405784X479    Support, Pivot
   8    150078            Screw, Hex Head  5/16-18 x 3/4
   9    189713X428    Knob, Defl ector

10    185600            Bolt, Shoulder
12    191730            Nut, Lock  1/4-20
13    72270505        Bolt, Carriage  5/16-18 x 5/8
14    179246            Washer, Nylon
15    404770X428    Chute Assembly
16    178633X428    Defl ector Assembly
17    179145            Seal, Defl ector
18    128415            Rivet, Blind
19    183333            Knob, Speed Control Lever
20    72270506        Bolt, Carriage  5/16-18 x 3/4
21    155415            Washer, Flat
25    198541            Nut, Lock  5/16-18
26    198475            Lever Assembly, Speed Control
27    169675            Retainer, Hairpin
28    180445            Rod, Upper, Speed Control
29    187716            Rod, Lower, Speed Control
30    192710            Clamp, Clean-Out Tool
31    192199            Tool, Clean-Out

NOTE:  All component dimensions given in U.S. inches.    1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your lawn mower and void your warranty.

Summary of Contents for 96192001100

































Reviews: