background image

3

duty, non-slip gloves; eye protection such

as non-fogging, vented goggles or face

screen; an approved safety hard hat; and

sound barriers (ear plugs or mufflers) to

protect your hearing.

Regular users

should have hearing checked regularly as

chain saw noise can damage hearing. Se-

cure hair above shoulder length.

Snug

Fitting

Clothing

Safety

Shoes

Safety Chaps

Heavy Duty

Gloves

Eye

Protection

Hearing

Protection

Safety Hat

S

Keep all parts of your body away from the

chain when the engine is running.

S

Keep children, bystanders, and animals a

minimum of 30 feet (10 meters) away from

the work area. Do not allow other people

or animals to be near the chain saw when

starting or operating the chain saw.

S

Do not handle or operate a chain saw when

you are fatigued, ill, or upset, or if you have

taken alcohol, drugs, or medication. You

must be in good physical condition and men-

tally alert. Chain saw work is strenuous. If

you have any condition that might be aggra-

vated by strenuous work, check with your

doctor before operating a chain saw.

S

Carefully plan your sawing operation in ad-

vance. Do not start cutting until you have a

clear work area, secure footing, and, if you

are felling trees, a planned retreat path.

OPERATE YOUR SAW SAFELY

S

Do not operate a chain saw with one hand.

Serious injury to the operator, helpers, by-

standers or any combination of these per-

sons may result from one-handed opera-

tion. A chain saw is intended for

two-handed use.

S

Operate the chain saw only in a well-venti-

lated outdoor area.

S

Do not operate saw from a ladder or in a

tree.

S

Make sure the chain will not make contact

with any object while starting the engine.

Never try to start the saw when the guide

bar is in a cut.

S

Do not put pressure on the saw at the end of

the cut. Applying pressure can cause you to

lose control when the cut is completed.

S

Stop the engine before setting the saw

down.

S

Do not operate a chain saw that is dam-

aged, improperly adjusted, or not com-

pletely and securely assembled. Always

replace bar, chain, hand guard, or chain

brake immediately if it becomes damaged,

broken or is otherwise removed.

S

With the engine stopped, hand carry the

chain saw with the muffler away from your

body, and the guide bar and chain to the

rear, preferably covered with a scabbard.

MAINTAIN YOUR SAW IN GOOD

WORKING ORDER

S

Have all chain saw service performed by a

qualified service dealer with the exception

of the items listed in the maintenance sec-

tion of this manual. For example, if improp-

er tools are used to remove or hold the fly-

wheel when servicing the clutch, structural

damage to the flywheel can occur and

cause the flywheel to burst.

S

Make certain the saw chain stops moving

when the throttle trigger is released. For

correction, refer to CARBURETOR AD-

JUSTMENT.

S

Never modify your saw in any way.

S

Keep the handles dry, clean, and free of oil

or fuel mixture.

S

Keep fuel and oil caps, screws, and fas-

teners securely tightened.

S

Use only Poulan accessories and replace-

ment parts as recommended.

HANDLE FUEL WITH CAUTION

S

Do not smoke while handling fuel or while

operating the saw.

S

Eliminate all sources of sparks or flame in

the areas where fuel is mixed or poured.

There should be no smoking, open flames,

or work that could cause sparks. Allow en-

gine to cool before refueling.

S

Always have fire extinguishing tools avail-

able if you should need them.

S

Mix and pour fuel in an outdoor area on

bare ground; store fuel in a cool, dry, well

ventilated place; and use an approved,

marked container for all fuel purposes.

Wipe up all fuel spills before starting saw.

S

Move at least 10 feet (3 meters) from fuel-

ing site before starting engine.

S

Turn the engine off and let saw cool in a

non-combustible area, not on dry leaves,

straw, paper, etc. Slowly remove fuel cap

and refuel unit.

S

Store the unit and fuel in an area where fuel

vapors cannot reach sparks or open

flames from water heaters, electric motors

or switches, furnaces, etc.

KICKBACK

WARNING:

Avoid kickback which

can result in serious injury.

Kickback

is the

backward, upward or sudden forward motion

of the guide bar occurring when the saw chain

near the upper tip of the guide bar contacts any

object such as a log or branch, or when the

wood closes in and pinches the saw chain in

the cut. Contacting a foreign object in the wood

can also result in loss of chain saw control.

S

Rotational Kickback

can occur when the

moving chain contacts an object at the up-

per tip of the guide bar. This contact can

cause the chain to dig into the object,

which stops the chain for an instant. The

result is a lightning fast, reverse reaction

which kicks the guide bar up and back to-

ward the operator.

Summary of Contents for 545186808





















Reviews: