Poulan Pro 115153026 Instruction Manual Download

Page: 1 / 21

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

P3818

Poulan

7349 Statesville Road

Charlotte, NC 28269

EN
G

LIS

ES
PA

ÑO
L

FR
ANÇA

For Occasional Use Only

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e en-

strucciones de seguridad. El no hacerlo puede resultar en lesiones

graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertisse-

ments et toutes les instructions de sécurité. Tout défaut de le faire

pourrait entraîner des blessures graves.

Poulan

850 Matheson Blvd. West

Mississauga, Ontario L5V 0B4

115153026

Rev. 4 3/15/10 BRW

Please do not return product to retailer.

Por favor, no devuelva el producto al lugar de compra.

Veuillez ne pas retourner le produit au détaillant.

1--800--554--6723

www.poulan.com

Register your product online at:

Registre su producto en línea en:

Enregistrez votre produit en ligne à l’adresse :

Summary of Contents for 115153026






















Search results

Summary of Contents for 115153026

Reviews:

Related manuals for 115153026

Brands by name

Popular brands

Poulan Pro 115153026, Instruction Manual

Search results

Summary of Contents for 115153026

Reviews:

Related manuals for 115153026

Brands by name

Popular brands