Poulan Pro 418774 Operator'S Manual Download Page 43

Page: 43 / 60

FIG. 17

SERVICE AND ADJUSTMENTS

WARNING: TO A

VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER

VICE OR AD JUST

MENTS:

•

Depress brake pedal fully and set parking brake.

•

Place attachment clutch in “DISENGAGED” position.

•

T urn ignition key to “STOP

” and remove key.

•

Make sure the blades and all moving parts have completely stopped.

•

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact

with

plug.

MOWER IS TO BE MOUNTED ON THE TRAC TOR,

REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS

(Q) INTO THE CABLE GUIDE ON FRONT EDGE OF

LOWER DASH.

TO INSTALL MOWER (See Fig. 18–21)

Be sure tractor is on level surface and engage park ing

brake.

•

Lower attachment lift lever to it's lowest position.

CAUTION: LIF

T LEVER IS SPRING

LOADED. HA

VE A TIGHT GRIP ON

LIFT LEVER, L

OWER IT SLOWL

Y AND

ENGAGE IN LOWEST POSITION.

NOTE:

Be sure mower side suspension arms (A) are point-

ing forward before sliding mower under tractor.

•

Slide mower under tractor until it is centered under

tractor.

•

ATT

ACH MOWER SIDE SUSPENSION ARMS (A) TO

CHASSIS - P

osition hole in arm over pin (B) on outside

of tractor chassis and secure with retainer spring.

•

Repeat on opposite side of tractor.

•

ATT

ACH REAR LIFT LINKS (C) - Lift rear corner of

mower and position slot in link assembly over pin (D)

TO REMOVE MOWER (See Fig. 17)

•

Place attachment clutch in “DIS EN

GAGED” position.

•

Lower attachment lift lever to its lowest position.

•

Roll belt off engine pulley (M) and belt keepers (G).

•

Remove retainer spring (K), slide col lar (L) off and push

housing guide (P) out of brack et.

•

Remove clutch cable spring (Q) from idler arm (R).

•

Disconnect front link (E) from mower - remove retainer

spring and washer.

•

Go to either side of mower and disconnect mower

suspension arm (A) from chassis pin (B) and rear lift

link (C) from rear mower bracket (D) - remove retainer

springs and washers.

CAUTION: AF

TER REAR LIFT LINKS

ARE DISCONNECTED, THE ATT

ACH-

MENT LIFT LEVER WILL BE SPRING

LOADED. HA

VE A TIGHT GRIP ON LIFT

LEVER WHEN CHANGING POSITION

OF THE LEVER.

•

Slide mower out from under right side of tractor.

IMPORTANT

IF AN ATT

ACHMENT OTHER THAN THE

Summary of Contents for 418774





























































Search results

Summary of Contents for 418774

Reviews:

Related manuals for 418774

Brands by name

Popular brands

Poulan Pro 418774, Operator'S Manual

Search results

Summary of Contents for 418774

Reviews:

Related manuals for 418774

Brands by name

Popular brands