Poulan Pro 418774 Operator'S Manual Download Page 38

Page: 38 / 60

FIG. 30

WEAK OR DEAD

BATTERY

FULL Y CHARGED

BATTERY

SERVICE AND ADJUSTMENTS

REPLACING BA

TTERY (See Fig. 31)

ARNING: Do not short battery ter mi

nals by allowing a wrench or any other

object to contact both terminals at the

same time. Before connecting battery,

remove metal bracelets, wristwatch

bands, rings, etc.

Positive terminal must be connected first to prevent spark-

ing from ac ci den

tal grounding.

•

Lift hood to raised position.

•

Disconnect BLACK battery cable (A) then RED battery

cable and carefully remove battery from tractor.

•

Install new battery with terminals in same position as

old battery.

•

First connect RED battery cable (B) to positive (+) battery

terminal with hex bolt and keps nut as shown. Tighten

securely. Slide terminal cover (C) over terminal.

•

Connect BLACK grounding cable to negative (-) bat

tery

terminal with re main

ing hex bolt and keps nut. Tight en

securely

• Close hood.

Positive

(Red)

Cable

Negative

(Black)

Cable

02954

FIG. 31

TO REPLACE HEADLIGHT BULB

• Raise hood.

•

Pull bulb holder out of the hole in the backside of the

grill.

•

Replace bulb in holder and push bulb holder securely

back into the hole in the backside of the grill.

• Close hood.

INTERLOCKS AND REL

AYS

Loose or damaged wiring may cause your tractor to run

poorly, stop running, or prevent it from starting.

•

Check wiring. See electrical wiring diagram in the

Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The

fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBL

(See Fig. 32)

• Raise hood.

•

Unsnap headlight wire connector.

•

Stand in front of tractor. Grasp hood at sides, tilt toward

engine and lift off of tractor.

•

T o replace, reverse above procedure.

03075

HEADLIGHT

WIRE

CONNECTOR

HOOD

ENGINE

TO AD JUST THROTTLE CON

TROL CABLE

The throttle control has been preset at the factory and

ad just

ment should not be necessary. If adjustment is nec-

sary, see engine manual.

TO AD JUST CHOKE CON

TROL

The choke control has been preset at the factory and ad-

just

ment should not be necessary. If adjustment is neces-

sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not

operate properly due to suspected carburetor problems,

take your tractor to an authorized service center for repair

and/or adjustment.

FIG. 32

TO ATT

ACH JUMPER CABLES -

•

Connect one end of the RED cable to the POSITIVE

(+) terminal of each battery(A-B), taking care not to

short against tractor chassis.

•

Connect one end of the BLACK ca

ble to the NEGA TIVE

(-) terminal (C) of fully charged battery.

•

Connect the other end of the BLACK cable (D) to good

chassis ground, away from fuel tank and bat tery

TO REMOVE CABLES, REVERSE ORDER -

•

BLACK cable first from chassis and then from the fully

charged battery.

•

RED cable last from both batteries.

Summary of Contents for 418774





























































Search results

Summary of Contents for 418774

Reviews:

Related manuals for 418774

Brands by name

Popular brands

Poulan Pro 418774, Operator'S Manual

Search results

Summary of Contents for 418774

Reviews:

Related manuals for 418774

Brands by name

Popular brands