background image

31

KEY   PART                
NO.    NO.                    DESCRIPTION

   1    196752X421    Wheel Assembly, 16", Power Steering, LH
   2    155443            Pin, Klik  1/4
   3    405161            Cover, Power Steering
   4    184471            Screw, Hex Head  #10-24 x 1/2
   7    17000616        Capscrew, Hex Head, Flanged  3/8-16 x 1
   8    185603X479    Bracket, Steering Cable, RH
   9    185602X479    Bracket, Steering Cable, LH

10    17600406        Screw, Hex Head  1/4-20 x 3/8

 11    198584            Screw, Hex Head  5/16-18 x 1/2

12    406057            Link, Steering Lever
13    193506X498    Yoke, Steering
14    182015            Pin, Steering Lever
15    194944X008    Bellcrank
16    194939X008    Bracket, LH Steering
17    194943X008    Bracket, RH Steering
18    181847            Pin, Steering Bellcrank
19    85179              Retainer, Hairpin
20    179148X479    Bracket, Steering
21    192126            Driver, Wheel
22    182466            Ring, Wire Retainer
23    187622            Lobe, Wheel
24    194941            Slide, Clutch
25    179139            Spring, Clutch Slide
26    194940            Lobe, Axle
27    189282            Key, Square  1/4 x .875
28    174697            Washer, Thrust (1")
29    179830            Bearing, Axle
30    193885            Spring, Return, Steering Latch
31    196753X421    Wheel Assembly, 16", Power Steering, RH
32    700279            Clip, Retainer
33    12000045        Ring, Retaining
34    146315            Screw, Hex Head, Tapping  5/16-18 x 5/8

KEY   PART                
NO.    NO.                    DESCRIPTION

   1    181037            Decal, Danger
   2    187867            Decal, Poulan Pro, 11 HP / 30"
   3    181035            Decal, Danger, Defl ector
   4    181042            Decal, Danger
   5    187892            Decal, Poulan Pro
   6    181033            Decal, Instruction
   7    155798            Decal, Traction Lever
   8    155800            Decal, Auger Lever
   9    181039            Decal, Speed Control

10    183730            Decal, Remote Defl ector Control

 11    183907            Decal, LH Trigger

12    183905            Decal, RH Trigger

  - -    406281            Owner’s Manual, English
  - -    406282            Owner’s Manual, French

NOTE:  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

REPAIR PARTS

 

SNOW THROWER - MODEL  

PP11H30ES

  (96192001400)

WHEELS / DECALS

Summary of Contents for 406281

































Reviews: