background image

8.0

INSTALLATION

22

Publication No. 5106451

8.6

Making the Gas Connection

1. Connect the gas supply to the RC

1

/

2

(

1

/

2

in BSPT

internal) gas tap located on the lower right side of

the boiler.

8.7

Fitting The Flue

Before fitting the flue, check the condensate

drain integrity (see section 8.5).

IMPORTANT:

The flue should always be installed

with a 3° (1 in 20) fall from terminal to elbow, to

allow condensate  to run back to the boiler.

HORIZONTAL FLUE

1. The standard flue is suitable for lengths 270mm

minimum to 800mm maximum (measured from the

edge of the flue elbow outlet).

Rear Flue:

maximum wall thickness - 630mm

Side Flue:

maximum wall thickness - 565mm (left or right)

2. 

For rear exit

- measure the wall thickness 

(Fig. 26) and to this dimension add 210mm. This

dimension to be known as (X).

i.e.

(X) = wall thi 210

3. Take the flue and mark off (X) from the terminal

end as indicated in the diagram 

(Fig. 27). 

Check your dimensions.

The flue tubes are fixed together. Cut through both

tubes whilst resting the flue on the semi-circular

packing pieces. Deburr both tube ends. 

4. 

For side exit

- measure the distance from the

edge of the wall plate to the inner face of the wall

(Fig. 26) and to this dimension add the wall

thi 250mm. This dimension to be known as

(Z).

i.e.

(Z) = wall plate to wall + wall thi 250

5. Take the flue and mark off (Z) from the terminal

end as indicated (Fig. 27).

Check your dimensions.

The flue tubes are fixed together. Cut through both

tubes whilst resting the flue on the semi-circular

packing pieces. Deburr both tube ends.

IMPORTANT:

Check all measurements before

cutting.

NOTE:

When cutting ensure the cut does not

interfere with the inner flue support bracket 

(Fig. 27a).

360° Orientation

Inner Flue Support Bracket

Wall Thickness

(Z)

Edge of Wall Plate to Wall

Wall Thickness

(Z) = Side Exit

(X) = Rear Exit

Flue

Waste

Fig. 26

Fig. 27

Fig. 27a

(1 in 20)

Summary of Contents for Promax 15 HE













































Reviews: