background image

SECTION 6 

 

POTTERTON COMMERCIAL PRODUCTS DIVISION 

 

INSTALLATION, OPERATION AND MAINTENANCE MANUAL 

 

 

PAGE 32 

PARAMOUNT 

 

REMOVING HEAT EXCHANGER 

 

Remove Heat Exchanger PARAMOUNT 40 

 
Follow the steps below to completely remove the 
heat exchanger: 

• 

Burner must be removed 

• 

Close shut-off fitting for flow and return and 
drain boiler water 

• 

Disconnect plug for boiler sensor (flow and 
return) 

• 

Loosen 2 nuts on condensate sump and 
remove bracket 

• 

Loosen flow and return fittings on heat 
exchanger (flat sealing) 

• 

Unscrew mounting screw on heat exchanger at 
top left and loosen hex. rod (10 mm). 

• 

Lift heat exchanger from condensate sump and 
remove. 

 

PARAMOUNT 60/80 

 

• 

Burner must be removed 

• 

Close shut-off fitting for flow and return and 
drain boiler water. 

• 

Disconnect plug for boiler sensor (flow and 
return) 

• 

Loosen flow and return fittings on heat 
exchanger (flat sealing) 

• 

Disconnect cable from water pressure switch 

• 

Unscrew nut at pipe that replaces a pump. 
Take out return pipe. 

• 

Disconnect plug from gas valve, take out gas 
valve. 

• 

Loosen 2 nuts on condensate sump and 
remove bracket. 

 

Remove air vent 

Unscrew nuts in the metal sheet from the black 
casing and lift heat exchanger with metal sheet 
from the condensate sump. 
 

• 

To clean the heat exchanger, rinse off with soft 
water jet (without additives). 

• 

After completing the cleaning work, reinstall 
heat exchanger and burner 

• 

Check the nominal heat load and CO

2

 emission 

values.

 

 

 

 

 

Fig. 11 Electrodes 

Summary of Contents for Paramount 40



















































Reviews: