manualshive.com logo in svg

Potter PVC 100, Installation Instructions Manual, Page: 11 / 12

Share
Download
Potter PVC 100 Installation Instructions Manual Download Page 11

PVC Specifications

Communications Bus:

 The communications bus conforms to the RS-485 standard and requires the use of 

UTP- cable for 1M Baud data rates. Wiring must be run in conduit in a daisy chain from the Master Panel to 
the first Dist. Panel, from each Dist. Panel to the next Dist. Panel and from the last Dist. Panel back to the 
Master Panel. When style 7 wiring is used, a separate conduit for each bus must be used.

Voltage: 5V peak-to-peak max.
Current: 50mA max.
Impedance: 120 Ohms
 (max. imp. between panels)
Frequency: 1.024MHz

Power Requirements:

 Power supplied to the DCC module is routed to any attached peripherals. These 

peripherals in turn determine whether the DCC is part of a Master Panel or a Dist. Panel.  Amplifier modules 
in Dist. Panel are powered separately and provide 24 VDC power to the panel.

Master Panel

Input Voltage 

 

120 Vac @ 60 Hz

Input Current 

 

0.28 A @ 120 Vac

Input Current (Battery) 

0.28 A  

Typical Load  

0.4 A

 Maximum Load

Battery Charging Current 

800 mA

Minimum Battery Size 

24V 7 AH

Maximum Battery Size 

24V 18 AH

Battery Type 

 

(2) 12V Gel Cell (in Series) 

Two 7 AH batteries is the maximum size that will fit in the Master Panel, larger batteries must be housed in a separate Listed 
Battery enclosure.

For a Master Panel that is wired with a 240 VAC Transformer the following ratings apply:

Input Voltage 

 

240 Vac @ 50 Hz

Input Current 

 

0.27 A @ 240 Vac

Distributed Panel

Maximum battery size is 18Ah for PVC-25E and PVC-50E.
Maximum Battery size for PVC-100E is 24 AH.

Two 12 AH batteries is the maximum size that will fit in the Distributed Panel, larger batteries must be housed in a separate 
Listed Battery enclosure.

See Table on following page for amplifier Electrical Ratings

Electrical Ratings    All circuits @ 24 VDC

MASTER PANEL

        

Stand By Condition       

 Alarm Condition

DCC                             

23mA   

 

 

33mA

ASC                              

83mA   

 

 

83mA

MMC                             

46mA   

 

 

46mA

MFP                             

  9mA                           

  9mA

MFH   

 

 

 

18mA   

 

 

21mA

IOI 

 

 

 

 

18mA   

 

 

19mA

SSC   

 

 

 

28mA   

 

 

28mA

SLC   

 

 

 

0.2mA  

 

 

16mA

TOTAL 

 

 

 

225.2   

 

 

255mA

DISTRIBUTED PANEL

  

Stand By Condition   

Alarm Condition

DCC    

 

 

 

82mA   

 

 

84mA

MBR   

 

 

 

31mA   

 

 

31mA

AMI 

 

 

 

 

22mA   

 

 

22mA

FPI 

 

 

 

 

41mA   

 

 

41mA

MBK   

 

 

 

  3mA   

 

 

31mA

TOTAL 

 

 

 

179mA 

 

 

209mA

page 11

Summary of Contents for PVC 100













Reviews:

No comments