manualshive.com logo in svg

Potter PSB-10, Installation, Operation And Instruction Manual

Share
Download
Potter PSB-10 Installation, Operation And Instruction Manual Download Page 22

PSN-64:2

PSN-106, PSN-64, PSB-10 • 5403590 • REV A • 12/09

The fi re alarm system employing this power supply must be designed by people trained and competent in the design and 
layout of fi re alarm systems. The system shall be designed and installed in accordance with all local and national codes and 
ordinances as well as the approval of the Authority Having Jurisdiction. Only trained, qualifi ed and competent individuals 
should install, program and/or service the POTTER FIRE POWER SUPPLY. Competent people would be aware of these 
warnings, limitations, and requirements.

High voltage electrocution hazard. Do not handle live AC wiring or work on the device while AC power is active.

This manual is designed to help with the specifi cation, installation, and programming of the POTTER FIRE POWER 
SUPPLY. It is imperative that this manual be completely read and understood before the installation or programming of the 
power supply. Save this manual for future reference.

Summary of Contents for PSB-10

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands