background image

 

 

Page 17 

required drivers  will be available on our web: http://www.posiflex.com. Then 
follow instructions from your system integrator for software recovery. 

Operating System Installation 

 

This  product  is  highly  professionalized  equipment.  The  installation  of  an  OS 
into  a  machine  without  any  preloaded  OS  could  be  a  major  difficulty  for 
average  user  or  obstacle  by  possibly  unintentional  negligence  even  for  PC 
veterans  to  accomplish  such  a  task.  Therefore,  OS  installation  into  a  system 
without  preloaded  OS  is  highly  discouraged.  Posiflex  Technology,  Inc.  shall 
not be responsible for any technical support to questions on this aspect. 

 

APPLICATION ENVIRONMENT 

 

It is 

very

 important that you check the following operational guidelines: 

 

Ventilation 

 

This  terminal  must 

NOT

  be  operated  in  an  environment  with  restricted 

ventilation. There must be at least 25 mm air clearance around any top or side 
ventilation  holes  with a free flow of air around the  unit at 

ALL

 times for the 

installation. 
 

Operating Environment 

 
The equipment must not be operated or stored in extremes of both temperature 
and  humidity/moisture.  (Operating  range  0°C  to  40°C  and  up  to  80% 
humidity – none condensing, max. wet bulb 26

°

C) 

 

UPS Battery (option) 

General care: 

 

The  UPS  battery  is  consumables  beyond  product  warranty.  Please  definitely 
observe  the  alerts  in  beginning  of  this  manual.  Please  always 

disconnect

  the 

battery if the system is to be powered off for more than few days. Reconnect it 
and turn on the system to recharge the battery for 1 ~ 2 hours every 3 months / 
every month for temperature lower than / over 30

°

C. Temperature above 

40°C 

must  be  strictly  avoided

  as  it  could  cause  termination  of  battery  life  and 

Summary of Contents for XP-3000 Series





















Reviews: