POSIFLEX PP-8900 User Manual Download

Page: 8 / 16

Restore LAN Information to Factory Default via LAN Info Reset

Among multiple built-in functions,

LAN Info Reset

mainly allows you to

reset LAN information to factory default. The following steps are provided to
help you complete the reset process.

Power OFF

printer.

Open the cover of the printer.

Press

Feed

button five times after powering on the printer.

Close the cover of the printer.

The printer will emit one long beep sound and then print a test
page displaying LAN interface information.

Afterwards, the printer will restart by itself.

Ensure that LAN information is correctly set to factory default
as follows:

LAN Interface Information for Factory Default

IP Address

192.168.192.168

MAC Address (*)

00.19.17.00.02.03

NETMASK

255.255.255.0

GATEWAY

192.168.192.1

LINK STATUS(*)

DISCONNECT

FIRMWARE VERSION(*)

1.1.2

Note:

Values of the Items marked with an asterisk (*) are

reserved and not allowed to be changed.

Summary of Contents for PP-8900

















Search results

Summary of Contents for PP-8900

Reviews:

Related manuals for PP-8900

Brands by name

Popular brands

POSIFLEX PP-8900, User Manual

Search results

Summary of Contents for PP-8900

Reviews:

Related manuals for PP-8900

Brands by name

Popular brands