background image

 

 

Part 10 

The  following  table  depicts  the  usage  of  all  the  ports  under  service  window. 
However,  it  is  highly  recommended  only  the  trained  or  certified  technician 
should  configure  the  DIP  switch,  for  incorrect  configurations  might  cause 
unexpected results or even damage the terminal. 

Label 

Description 

LPT 

Connects to the parallel device via a conversion cable. 

SATA1 

Connects to eternal SATA HDD. 

PWR1 

Connects to external SATA HDD for supplying power. 

 

DIP Switch 

Description 

1 On 

2 Off 

Default 

1 Off 

2 On 

Clear CMOS 

Off 

Linux or WinCE 

On 

Windows OS (Default) 

Off 

Fujitsu Touch Panel 

On 

ELO Touch Panel or ABON Touch Panel 

Off 

Windows/Linux/Win CE (Default) 

On 

MS-DOS 

Off 

Enable On Board USB Touch  

On 

Disable On Board USB Touch 

Off 

Reserved 

On 

Reserved 

Off 

Reserved 

 

SIDE MOUNT UPGRADE KIT (OPTION) 

Remove  the  2  screws  circled  in  the  left 
picture  to  remove  the  cover  for  side 
mount  upgrade  kit.  Take  out  the  cable 
inside  this  cover  and  connect  it  to  the 
white  connector  inside  the  side  mount 
upgrade  kit  like  SD-500  series  as 
arrowed  in  the  right  picture.  Gently 
arrange the excessive length of this cable 
back in the hole and screw-fit it back to 

the  position  originally  occupied  by  the  cover.  Please 
reserve the cover if there is chance to have the side mount kit removed in the 
future. 
 

Summary of Contents for KS - 7212/X

















Reviews: