POSI LOCK PH-100T, Instructions-Parts List Manual

Page: 13 / 16

25 24
QUANTITY
PART # DESC. 100T/123T 102T 200T
HT-2111AR 200-Ton Mast - - 1
HT-2112 200-Ton Puller Slide - - 2
HT-ST1 Steel Tube 1 1 1
HT-ST2 Steel Tube 1 1 1
HT-ST3 Steel Tube 1 1 1
HT-ST4 Steel Tube - 1 1
HT-ST5 Steel Tube 1 1 -
HT-VC4 4-Way Valve 1 1 2
HT-CH604 Male Coupler - - 3
HT-VC20 4-Way Closed Center Valve 1 1 1
HT-V82 Needle Valve 1 1 1
HT-CR400 Female Coupler - - 3
PH-10010 100-Ton Cylinder 1 1 -
PH-2022 Electric Pump 1 1
PGB254TLM Gauge 1 1 1
HT-GA3 Gauge Adapter 1 1 1
PH-411 Dust Cap 3 3 -
PH-927 Hose 10' 1 - 1
FHCH-38M Male Coupler 3 3 -
FHCH-38F Female Coupler 3 3 -
200-Ton Hydraulic Pump - - 1
POSI LOCK® 100-TON & 200-TON
Hydraulic Puller Systems
Parts List (continued)
FLOW DIVIDERS Delta Power Company
4484 Boeing Drive - Rockford, IL 61109
WARNING: The specifications/application data shown in our catalogs and data sheets are intended only as a general guide for the product described
(herein). Any specific application should not be undertaken without independent study, evaluation, and testing for suitability.
Phone: (815) 397-6628 Fax: (815) 397-2526 E-mail: delta@delta-power.com
Delta Power Rotary Flow Divider, Positive Displacement
Delta Series P geared flow dividers, accurately divide flow from a single hydraulic
source into two or more equal or proportionate circuits. In like manner, the input
pressure required will be proportional to levels of flow/pressure out of the flow divider,
rather than at the highest pressure level, thereby saving what would normally be
wasted energy. Proven design, stable material selection and precision machining are
the Delta keys to reliable performance you can depend on in a variety of applications.
Application Suggestions
1. For greatest efficiency and accuracy, flow dividers should be used at near
maximum rated inlet gallonage. For quieter operations, lowered RPM should
be considered.
2. Maximum (3500) and minimum 500 RPM; inlet pressure ratings and differential
pressure ratings should be followed.
3. Provide over-pressure protection (relief valves) in each circuit.
4. When designing flow dividers into a static circuit, remember that they are
dynamic devices which do nothing while static.
5. Use SAE 10 through SAE 30 industrial petroleum-based hydraulic oil with 200
SSU viscosity; filter to 25 microns.
6. Do not use teflon tape in installation. Use plastic pipe sealant with NPTF ports.
• High-strength permanent mold cast iron housing
• Precision needle bearings
• Precise machined trapping relief grooves provide
constant filling and discharging to assure quiet
operation and maximum bearing life.
• O-ring seals between sections (Buna-N)
Where one pump operates a
number of hydraulic motors: car
wash systems lubrication systems
(multiple point), hydraulic motor
driven machines, (harvesting
machinery, etc.)
Where two or more cylinders must
be synchronized: lift platforms,
scaffolds, presses.
Where main pump pressure must be
intensified in one circuit of multiple
circuit machinery, such as waste
compactors and other hi-lo
applications.
Where two or more circuits must be
controlled independently at different
pressures: presses, machine tools,
etc.
Page 36
POSI LOCK® 100-TON & 200-TON
Hydraulic Puller Systems
Flow Dividers