Portwell WEBS-5491 User Manual Download Page 10

Page: 10 / 46

System Installation

WEBS-5491 Embedded System User’s Manual

2-2

Solder side:

Connector and Jumper setting:

Connector
J3

DDR3 SO-DIMM Socket.

Compact Flash connector.

PCI-E X 1 Slot.

Mini-PCI-E Slot.(Half size)

SATA Connector with power.

GPIO Connector.(2*5 Pin/2.0mm)

SM- Bus Connector.

J10

Battery Connector.

J11

PCI-E X4 Slot(Right angle) for Audio and COM Port Signal .

J12

USB Port 0~1 D-Sub Connector. (Up:USB2.0 Down:USB3.0)

J13

RJ45 Connector.

J14

RJ45 Connector.

J15

DVI-I D-sub Connector.

J16

Power Input Connector. (Terminal Blocks 3Px1/5.08mm female)

J19

SD Card.

J22

USB Port 3 Connector (1*4 Pin Wafer/2mm).

Jumpers
JP1

Clear CMOS.

JP7

GPIO Voltage selection.

JP8

Audio out.(From amplifier)

JP9

LPC Debug Port.

JP10

COM PORT RI and power source adjust pin.

Summary of Contents for WEBS-5491















































Search results

Summary of Contents for WEBS-5491

Reviews:

Related manuals for WEBS-5491

Brands by name

Popular brands

Portwell WEBS-5491, User Manual

Search results

Summary of Contents for WEBS-5491

Reviews:

Related manuals for WEBS-5491

Brands by name

Popular brands