manualshive.com logo in svg

PORTMAN TLU100N, Operation And Installation Manual

Share
Download
PORTMAN TLU100N Operation And Installation Manual Download Page 16

In Commercial Confidence 
 

15

141

 

  Power of temperature sensor is low 

144  Exit defined Circular Geofence area4 (Self Geofence) 
145

 

Enter defined Circular Geofence area4 (Self Geofence) 

150

 

‘Help’ request 

151

 

User Duty on 

152  User Duty off 
154  Exit defined Circular Geofence area5 
155  Enter defined Circular Geofence area5 
156 Door Close (Wireless Door Sensor 1) 
157 Door Open (Wireless Door Sensor 1) 
158 Door Close (Wireless Door Sensor 2) 
159 Door Open (Wireless Door Sensor 2) 
160 Door Close (Wireless Door Sensor 3) 
161 Door Open (Wireless Door Sensor 3) 
162 Door Close (Wireless Door Sensor 4) 
163 Door Open (Wireless Door Sensor 4) 
164  Exit defined Circular Geofence area6 
165  Enter defined Circular Geofence area6 
166 Tamper Switch Close (Wireless Door Sensor 1) 
167 Tamper Switch Open (Wireless Door Sensor 1) 
168 Tamper Switch Close (Wireless Door Sensor 2) 
169 Tamper Switch Open (Wireless Door Sensor 2) 
170 Tamper Switch Close (Wireless Door Sensor 3) 
171 Tamper Switch Open (Wireless Door Sensor 3) 
172 Tamper Switch Close (Wireless Door Sensor 4) 
173 Tamper Switch Open (Wireless Door Sensor 4) 
174  Exit defined Circular Geofence area7 
175

 

Enter defined Circular Geofence area7 

184  Exit defined Circular Geofence area8 
185  Enter defined Circular Geofence area8 
194  Exit defined Circular Geofence area9 
195

 

Enter defined Circular Geofence area9 

230

 

[on/off] SEND REPORT IF ADC1 LESS THAN [min voltage] V for [debounce time] SEC, RESEND PER [resend 
time] SEC   

231

 

[on/off] SEND REPORT IF ADC1 MORE THAN [max voltage] V for [debounce time] SEC, RESEND PER 
[resend time] SEC   

232

 

[on/off] SEND REPORT IF ADC1 GO UP [up voltage] V for [debounce time] SEC   

233

 

[on/off] SEND REPORT IF ADC1 GO DOWN [down voltage] V for [debounce time] SEC   

234

 

[on/off] SEND REPORT IF ADC1 ENTER [min voltage] V TO [max voltage] V for [debounce time] SEC    

235

 

[on/off] SEND REPORT IF ADC1 EXIT [min voltage] V TO [max voltage] V for [debounce time] SEC 

 

 
Point Geofence report event 
280  Enter point Geofence 0 
281  Enter point Geofence 1 
282  Enter point Geofence 2 
283  Enter point Geofence 3 

Summary of Contents for TLU100N






















Reviews:

No comments

Brands by name

Popular brands

Load more brands