background image

USER MANUAL 

 Portman Custom Lights P3 PIX3L

Menu 

Navigation buttons are located under the LCD display on the back panel. To enter the menu hold enter 
button for 2 seconds. To navigate the menu 

use the “+” and “

-

“ buttons

. To exit the menu from any level 

hold enter for 2 seconds or use the exit function. For confirming simply push the enter button. 

 

 

 

 

 

 

 

Menu map 

Main section 

Level 1 

Description  

ADDRESS 

1 - 509

 

Sets up the DMX start address.  

DMX INPUT 

WIRED

 

Changes the  DMX  input  to  wired  (default).  In  this  mode 
fixture is receiving DMX signal from the DMX IN 5 pin XLR 
socket. 

WIRELESS

 

Changes the DMX input to wireless. This mode works only 
when  WDMX  card  is  installed.  Fixture  is  receiving  DMX 
data from WDMX card.  

RDM INFO 

MANUFACTURER 

Shows the name 

of the fixture’s manufacturer.

 

DEVICE NAME 

Shows the fixture’s name given by manufacturer.

 

DDEVICE LABEL 

Shows the fixture’s name given by user.

 

RDM ID 

Shows the fixture’s RDM unique ID number.

 

UNPAIR WDMX  

 

Unlinks  all  linked  Wireless  Solution  Sweden  WDMX 
transmitters.  

MANUAL 

CONTROL 

ALL CHAN: 

0-100% 

Controls the intensity of all channels at once. 

CHAN. 1 

0-100% 

Individually controls the intensity of selected channel.  

CHAN. 2 

0-100% 

CHAN. 3 

0-100% 

EXIT 

 

Exits from main section of the menu to main screen.  

 

Summary of Contents for P3 PIX3L

















Reviews: