background image

 

 

                                                                                                   

19 

(12)

 

GPRS

 DIAL

-

UP PROCEDURE

 

 

1) GPRS always one-line 

Parameters: Reconnect interval 

While using this mode, when the unit can not searched GPRS signal, system will reconnect 

GPRS interval a preset value. (e.g.: 1minute) 

 

2) Based on report mode 

Parameters: Max. reconnect times, reconnect interval 

While using this mode, the unit will connect to the server when there is a report to send. If 

the first connection is failed, it will retry to connect to the server up to the max. reconnect 

times. Each retry will be separated by the reconnect “interval”. 

 

3) GPRS connect once 

While using this mode, the unit will connect to the server when there is a report to send (but 

only try once). If it is not successful, the report will be stored and sent out in the next 

successful connection. Disconnect GPRS connection when report sending is completed. 

 

4) Reduce dialup attempts 

Parameters: On/Off, Max. reconnect times, connect delay 

If this method is used, the unit will reduce dialup attempts when attempting to reconnect 

more than reconnect times. User can define the delay time for the unit before try to 

reconnect to the server. If there is trigger report, the unit will connect to server immediately. 

 

Special command for SMS mode: 

Summary of Contents for GT3000 SERIES





























Reviews: