English
6
the battery. Return it to a service center or a collection site
for ecycling.
Hot/Cold Pack Delay
When the charger detects a battery that is excessively
hot or excessively cold, it automatically starts a Hot/Cold
Pack Delay, suspending charging until the battery has
normalized. After this happens, the charger automatically
switches to the Pack Charging mode. This feature ensures
maximum battery life. The light flashes in the pattern
indicated on the label.
Leaving the Battery in the Charger
The charger and battery pack can be left connected with
the LED glowing indefinitely. The charger will keep the
battery pack fresh and fully charged. This charger features
an automatic tune-up mode which equals or balances the
individual cells in the battery pack to allow it to function at
peak capacity. Battery packs should be tuned up weekly or
whenever the battery no longer delivers the same amount
of work. To use the automatic tune-up mode, place the
battery pack in the charger and leave it for at least 8 hours.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the radio from
the AC outlet before cleaning. Dirt and grease may be
removed from the exterior of the radio using a cloth
or soft non-metallic brush. Do not use water or any
cleaning solutions.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65 °F and 75 °F (18 ° – 24 °C). DO NOT charge
the battery pack in an air temperature below +40 °F
(+4.5 °C), or above +104 °F (+40 °C). This is important
and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Unplug the
charger before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
nOTE:
Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)
WARNING:
Never modify the charger, radio or any
part of it. Damage or personal injury could result.
Refer to Fig. A at the beginning of this manual for a
complete list of components.
INTENDED USE
This charger / radio is designed for broadcast radio
reception, to play/stream audio through a wired connection
to a mobile phone or other audio device, and to charge
PORTER-CABLE batteries.
DO nOT
use under wet conditions or in presence of
flammable liquids or gases.
DO nOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
OPERATION
To Install Coin Cell Battery (Fig. B)
Your radio is equipped with memory capacity in order to
store the preset time. When the radio is in the OFF position,
this memory capacity is powered by one coin cell battery
that is included with the radio.
nOTE:
For first time use, remove the protective tab under
the battery door to activate the coin cell battery.
WARNING:
Danger of explosion if battery is
incorrectly replaced. When replacing battery, replace
it with the same or equivalent type CR2032. Observe
correct polarity (+ and –) when replacing batteries.
Do not store or carry batteries so that metal objects
can contact exposed battery terminals.
1. On the battery door
14
on the back of the unit, turn
the screw
16
counterclockwise to remove. Screw will
remain captive in the door.