English
8
Cold Weather Operation
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories.
An accidental actuation
can cause injury.
WARNING:
Do not store tools in a cold weather
environment to prevent frost or ice formation on the
tools operating valves and mechanisms that could
cause tool failure.
WARNING:
Some commercial air line drying
liquids are harmful to “O”‑rings and seals – do
not use these low temperature air dryers without
checking compatibility.
When operating tools at temperatures below freezing:
1. Make sure compressor tanks have been properly drained
prior to use.
Depth Adjustment (Fig. A, E)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories.
An accidental actuation
can cause injury.
The depth that the fastener is driven can be adjusted using
the depth adjustment wheel.
1. To drive the fastener shallower, rotate the depth
adjustment wheel
6
to the right.
2. To drive a fastener deeper, rotate the depth adjustment
wheel
6
to the left.
Clearing a Jammed Nail (Fig. A, H, I)
WARNING:
Disconnect the tool from the air supply
and remove fasteners from magazine before making
adjustments or personal injury may result.
If a nail becomes jammed in the nosepiece, keep the tool
pointed away from you and follow these instructions to clear:
1. Disconnect the tool from the air supply.
2. Release magazine release
6
from behind nails.
3. Push down jam clearing latch
2
then pull up to open
front door
16
.
4. Remove bent nail, using pliers if necessary.
5. If driver blade is in the down position, insert screwdriver
or other rod into nosepiece and push driver blade back
in position.
6. Remove rod and close front door.
7. Lift latch to secure door to nosepiece.
8. Reinsert nails into magazine (see
Loading the Tool
).
9. Release magazine release
6
.
10. Reattach air supply.
nOTE:
Should nails continue to jam frequently in nosepiece,
have tool serviced by an authorized service center.
Actuating Tool
WARNING:
To reduce the risk of injury, Always wear
proper eye [ANSI Z87.1 (CAN/CSA Z94.3)] and hearing
protection [ANSI S12.6 (S3.19)] when operating
this tool.
The tool can be actuated using one of two modes:
single sequential action trigger mode and bump action
trigger mode. The trigger installed on the tool as described
in the
Trigger
section of this manual determines the mode
of operation.
Sequential Action Trigger -
Gray
Trigger (Fig. A)
The sequential action trigger’s intended use is for
intermittent fastening where very careful and accurate
placement is desired.
To Operate the nailer in sequential Action Mode
1. Depress the contact trip firmly against the work surface.
2. Pull the trigger.
WARNING:
A fastener will be driven each time the
trigger is pulled as long as the contact trip remains
depressed which could result in accidental driving.
Bump Action Trigger -
Black Trigger
(Fig. A)
The bump action trigger’s intended use is for rapid fastening
on flat, stationary surfaces.
Using the bump action trigger, two methods are available:
place actuation and bump actuation.
To Operate the Tool Using the Place Actuation Method
1. Push the contact trip against the work surface.
2. Pull the trigger.
3. Release the trigger and allow the tool to recoil off
the workpiece.
To Operate the Tool Using the Bump Actuation Method
1. Pull the trigger.
2. Push the contact trip against the work surface. As long
as the trigger is pulled, the tool will drive a fastener every
time the contact trip is depressed. This allows the user to
drive multiple fasteners in sequence.
Loading Fasteners (Fig. G)
WARNING:
Keep the tool pointed away from yourself
and others. Serious personal injury may result.
WARNING:
Never load fasteners with the contact trip
or trigger activated. Personal injury may result.
WARNING:
Always disconnect the tool from the air
supply before making any adjustments or attemping
any repairs to the tool.
The PORTER‑CABLE finish nailers are equipped with load and
lock magazines.
Load And Lock Method
1. Lock‑off trigger
1
.
2. Insert fasteners into the rear of the magazine
5
.
3. Pull pusher
7
back until the nail follower falls behind
the nails.
WARNING:
Do not keep trigger pulled when tool is
not in use.
