Porsche 928S 1983 Driver Manual Download Page 93

Page: 93 / 110

Motor Oils

Use only branded HD oils which satisfy the

API classification API SE or SF for gasoline
engines. These classifications are often given
together with the classifications for diesel en-
gines, e. g., SE/CC, SF/CC or SF/CD.

Single-grade, multigrade and fuel-economy
oils can be mixed provided the viscosity grades
correspond to outdoor temperatures.

Single-Grade Oils

Single-grade oils may only be used when
multigrade oils are not available and the car is
being used under normal conditions. To pre-

vent damage, the oil must be changed as re-
quired when temperatures change consider-
ably.

Multigrade Oils

The oil change intervals given in the service
schedule apply when multigrade oils are used.

For all-season use only the multigrade oils

indicated the table opposite may be used, in
accordance with prevailing air temperatures.

Fuel-economy Oils

In addition to single-grade and multigrade oils,
"fuel-economy" oils are available (developed

for all-year round use). Before using these

unconventional oils, consult your authorized
Porsche dealer.

Summary of Contents for 928S 1983















































































































Search results

Summary of Contents for 928S 1983

Reviews:

Brands by name

Popular brands

Porsche 928S 1983, Driver Manual

Search results

Summary of Contents for 928S 1983

Reviews:

Brands by name

Popular brands